Paradyne GranDSLAM 4200 manual Uplink Module Connectors, 4201 T1 Uplink Module Connector

Page 27

2. Cabling

Uplink Module Connectors

he following types of uplink modules are available for the unit:

Model 4201 T1 Uplink Module

TModel 4202 E1 Uplink Module

Model 4203 T1/E1 IMA Uplink Module

4201 T1 Uplink Module Connector

The 4201 T1 Uplink Module has a single RJ48C, 8-pin, unkeyed, shielded connector.

NOTE:

The metal shell of the T1 connector is grounded. Pins 7 and 8 of the connector are not grounded. Therefore, if the cable you are using is wired to ground the cable shield to pins 7 and 8, you must first obtain a cable with a shielded plug and connect the cable shields (drain wires) to the plug’s shield. If your cable has separate shields for transmit and receive, you must ground both drain wires. You can also ground the shields at the far end, or you can use a nonshielded cable.

Procedure

To connect to the 4201 T1 Uplink Module:

1. Determine the interface type, and procure the appropriate cable.

2. Plug the 8-position modular plug into the 100modular jack.

RTN -

 

 

 

 

48VDC

3.5

 

 

ALAR

B

A

60

 

 

 

M

A

 

 

 

C

 

 

 

 

ONS

 

 

 

 

OLE

PO

 

 

 

 

WER

 

A

B

 

 

 

B

 

 

 

 

 

 

 

ITS

 

 

 

 

M

 

 

 

 

GMT

S

K

U

T

IN

A L

T P

S U

MT R S L E A T

4201 T1 MODULE

100

1

4

 

 

8

12

 

 

13

16

 

 

20

24

 

 

8-Position

Modular02-17275

Plug

3.Connect the other end of the cable to the appropriate network equipment such as a multiplexer.

4200-A2-GN20-10

October 2002

2-3

Image 27
Contents GranDSLAM ATM Stackable Dslam Copyright 2002 Paradyne Corporation All rights reserved Important Safety Instructions United States EMI Notice Japan October Contents LEDs ConfigurationConnectors and Pin Assignments Equipment List Technical Specifications IndexNew Features for This Release About This GuideDocument Purpose and Intended Audience Related Product Documents Document SummaryOverview InstallationPreparation Installation SiteDSL Ports Cables RequiredUnpacking the Hardware Package ContentsFlat-head screw for attaching 19 mounting brackets to Mounting Configurations Installing the Brackets for Rack MountingMounting Brackets Inch 483 mm Rack Mount Installing the GranDSLAM 4200 Into a Rack Inch 584 mm Nortel Rack Mount Installing the GranDSLAM 4200 on a Wall 18.75 in 476.25 mm Installing the GranDSLAM 4200 on a Shelf or Desktop Installing the Uplink Module 02-17267 Cabling Overview CablingDSL Ports 4201 T1 Uplink Module Connector Uplink Module Connectors4202 E1 Uplink Module Connectors Coaxial 4203 T1/E1 IMA Uplink Module Port Connectors ATM Installing the 4203 T1/E1 IMA Uplink DSL Cable Ferrite Choke Management Port Console Console PortSerial Port Modem Alarm Bits Alarm InterfaceSpring Tab Model Grounding Lug Power Connector Insert Into Cabling October LED Locations LEDsLED LED MeaningsConventions Used ConfigurationUsing the CLI Rtrv ? GranDSLAM 4200 Turn-up ProcedureTurn-up Procedure for Out-of-Band Management Turn-up Procedure for Inband ManagementConfiguring the Unit for Operation Configuration October Connectors and Pin Assignments DSL Ports and Pots Splitter Connectors Console Port Connector Management Port ConnectorModels 4220/4230 ALARM/BITS Connector Model 4210 ALARM/BITS Connector4201 T1 Uplink Module Connector 4202 E1 Uplink Module Connectors 120Ω Connector75Ω TX/RX Connectors 4203 T1/E1 IMA Uplink Module Port Connectors Connectors and Pin Assignments October Equipment List Hardware, and Installation GuideEquipment List 4222-A1-532 Includes Installation Instructions DSL Technical SpecificationsConsole Numerics IndexIN-2 IN-3 IN-4