Patton electronic Model 3088/I manual Installation, Operation, Power-up

Page 33

3088/I Getting Started Guide

5 • Installation & operation

 

 

Installation

Once the Model 3088/I is properly configured, it is ready to connect to the twisted pair interface. This section tells you how to make the connection.

Connecting the twisted-pair interface

The Model 3088/I supports communication between two DTE devices as follows over 2-wire single twisted- pair (TP).

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, flammability, and

CAUTION mechanical serviceability.

Two things are essential:

1.These units work in pairs. Both units at the end of the twisted pair DSL span must be set for the same DTE rate—one unit set as CO, the other as CP.

2.To function properly, the Model 3088/I needs one twisted pair of metallic wire. This twisted pair must be unconditioned, dry, metallic wire, between 19 (0.9mm) and 26 AWG (0.4mm) (the higher number gauges will limit distance). Standard dial-up telephone circuits, or leased circuits that run through signal equaliza- tion equipment, or standard, flat modular telephone type cable, are not acceptable.

The RJ-11 connector on the Model 3088/I’s twisted pair interface is polarity insensitive and is wired for a two- wire interface. The signal/pin relationships are shown in Appendix D on page 56.

Operation

Once the Model 3088/I is properly configured and installed, it should operate transparently. This section describes information for powering the 3088/I, reading the LED status indicators, and using the built-in loop- back test modes.

Power-up

(Also refer to “Power up the NTU” on page 17.)

Ensure that the power cable used with the external power adapter meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

WARNING

The Model 3088/I uses a 5 VDC, 2A universal input 100–240 VAC, power supply (center pin is +5V). The universal input power supply has a male IEC-320 power entry connector. This power supply connects to the Model 3088/I by means of a barrel jack on the rear panel. Many international power cords are available for the universal power supply (Please refer to Appendix C on page 54 for country-specific power cords.

The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 3088/I. See “DC power- up” on page 17 for information about installing the DC power adapter.

Installation

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents RocketLink-G G.SHDSL NTU Mailsupport@patton.com Summary Table of Contents Table of Contents Installation & operation Factory replacement parts and accessories RS-232 console interface pin assignments List of Figures List of Tables About this guide AudienceStructure Impaired functioning PrecautionsGeneral observations Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral information Chapter contentsRocketLink-G 3088/I overview FeaturesInitial configuration AC power-up Power up the NTUDC power-up IntroductionPower-up indication Configure the IP addressConnect a PC and log Connect to the local IP network Modify the IP addressConnect the G.SHDSL port Log onto the web management interfaceRear view of 3088/I showing DSL RJ-11 jack Shdsl config and status DSL Parameters DSL configurationDSL Error Monitor Configuration DSL Error Monitor ConfigurationRun-Time Statistics Shdsl StatusLocal Interface Error Counters DSL Line Error CountersClearing the error counters Clearing Error CountersEthernet & WAN PPP Config and status PPP configuration IP configurationEthernet port configuration Ethernet Basic Port AttributesEthernet performance statistics Ethernet Advanced Port AttributesConfigurable Ethernet parameters Installation & operation Power-up InstallationConnecting the twisted-pair interface OperationLED status indicators Power YellowWAN LEDs 100M Yellow Ethernet LEDsSystem Management 3088 RocketLink-G Plug ‘n’ PlayReset for Factory Default Saving the configurationConsole Backing up and restoring saved configurations AuthenticationUpgrading software on the 3088/I System Software UpgradeDiagnostic tools System tools for testing LED status monitor & definitionPing & Traceroute Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance SafetyFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityAuthorized European Representative Appendix B Specifications Shdsl characteristics General characteristicsEthernet Protocol supportDiagnostics Serial connectorManagement 10Base-T/100Base-TX interfaceVDC power supply PowerEthernet 100M Ethernet TxLine Interface DimensionsEnvironment Shdsl Physical connection & Transmission LineAppendix C Factory replacement parts and accessories Model # Description Factory replacement parts and accessoriesAppendix D RJ-11 non-shielded DSL port RJ-11 non-shielded DSL port Appendix E RJ-45 shielded 10/100 Ethernet port RJ-45 shielded 10/100 Ethernet port Appendix F RS-232 console interface Pin assignments RS-232 console interface pin assignments RJ-45 non-shielded Connector EIA-561
Top Page Image Contents