Patton electronic 6511RC user manual Setting up the HyperTerminal or similar program session

Page 44

3 • Configuring the Matrix Switch for operation	Model 6511RC User Manual

Setting up the HyperTerminal (or similar program) session

Do the following:

1.At your PC, find the file HYPERTRM.EXE. Open a HyperTerminal session by double-clicking on the file name.

Figure 21. Connection Description window

2.Type a connection name (e.g., 6511RC Config), select an icon, then click OK (figure 22).

Figure 22. Connect To window

3.On the Connect To window (figure 22), set Connect using: to one of the options named Direct to ComX (where the “X” refers to the number identifying the RS-232 serial port on the PC). In the following proce- dure, Com1 will be the used as the port identifier.

4.Click OK.

5.The COM1 Properties window displays.

44	Initial configuration through the RS-232 control port

Image 44

Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents Industry Canada Notice FCC Part 68 Acta StatementFacility Service Network Interface Code Connection CE NoticeAudience StructureGeneral conventions PrecautionsTypographical conventions used in this document Mouse conventions About this guide Chapter contents IntroductionModel 6511RC Matrix Switch overview Model 6511RC Matrix Switch front bladeModel 6511RC Matrix Switch major functions and interfaces Hardware overview Model 6511RCT rear bladeModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront chassis architectures ForeFront Model 6476 6U cPCI chassisForeFront Model 6676 9U chassis Model 6676 chassis, front viewMatrix Switch functionality TDM mapping and aggregationTDM bus architecture STM-1 link architectureMatrix Switch TDM capacity Matrix Switch Ethernet SwitchingManagement Services ManagementManagement Interfaces Management ApproachMatrix Switch Interfaces WAN InterfacesMid-Plane Interfaces LAN InterfaceSystem timing Power systemCentral processing unit Temperature Physical dimensionsLED Indicators AltitudeRear-panel LED indicators Approvals Etsi CTR EMCApprovals Hardware installation Introduction Unpacking the Model 6511RC Matrix SwitchVerifying that the ForeFront chassis is properly installed Verifying correct cover plate installation Verfying correct electrical groundingMatrix Switch hardware installation Alignment/ESD pin and card handleInstalling the network cables Matrix Switch front blade network interface portsConnecting the front-panel Ethernet LAN port Ethernet RJ-45 pin and signal definitions for Matrix SwitchConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors Connecting the rear-panel Ethernet WAN/management ports BNC coaxial cable connectorsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page overview Home page window panesOperator Actions buttons Configuring the default gateway IP OverviewConfiguring the system clocking parameters Module clocking modeModule clocking source and fallback An internal oscillator STM-1 portConfiguring the SDH circuit parameters System Clocking Configuration page, exampleAccessing the SDH circuit parameters SDH Overview web managementConfiguring the SDH physical interface type Configuring the SDH interface parametersConfiguring the SDH path trace parameters SDH Path Trace parametersConfiguring DS0 idle codes Accessing the idle code configuration E1 LinkDefining the DS0 idle code configuration Selecting the SDH mapping pathSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings Defining DS0 mappings using E1 port format DS0 Mapping OverviewExamples for configuring DS0 mappings Solution Solution Solution Defining DS0 mappings using TU format DS0 Mapping Overview page with TU format selectedE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution Saving your configuration RC HomeBacking up your configuration parameters Import/ExportBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown Activating the Model 6511RC De-activating the Model 6511RCTroubleshooting and maintenance Troubleshooting during initial deployment Cited in section De-activating the Model 6511RC onGeneral fault analysis PowerCLK Enet Matrix Switch test tools Loopback test modes for the STM-1 portMatrix Switch TDM mapping architecture Facility Loop sonetFacilityLoop1SDH Configuration page with sonetFacilityLoop1 selected Terminal loop sonetTerminalLoop2SDH Configuration page with sonetTerminalLoop2 selected Other Loop sonetOtherLoop3 SDH section trace and path traceSections and paths Section traceSection Trace parameters on the SDH Configuration Path tracePath Trace parameters on the SDH Configuration Number of paths per framePeriodic maintenance MaintenanceExporting the current Model 6511RC configuration CalibrationMaintenance Maintenance Removing the defective Model 6511RC Installing the replacement Model 6511RC Importing a saved configurationCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditShipping instructions Return for credit policyRMA numbers Contacting Patton for assistance 104