Patton electronic 6511RC user manual Hardware installation

Page 4

Contents	Model 6511RC User Manual

Temperature	27
Altitude	27
Humidity	27
Physical dimensions	27
LED Indicators	27
Approvals	29
2 Hardware installation	31
Introduction	32
Unpacking the Model 6511RC Matrix Switch	32
Verifying that the ForeFront chassis is properly installed	32
Verfying correct electrical grounding	33
Verifying correct cover plate installation	33
Matrix Switch hardware installation	34
Installing the network cables	35
Connecting the front-panel Ethernet LAN port	36
Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub	36
Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC	36
Connecting the front-panelEIA-561RS-232 configuration port (DCE configured)	37
Connecting the rear-panelSTM-1 WAN port to an SDH network	37
Connecting the STM-1 optical interface to fiber-optic network cables	37
Connecting the STM-1 electrical interface to coaxial network cables	38
Connecting the rear-panel Ethernet WAN/management ports	39
Connecting the 10/100/1000 Base-T Ethernet ports to a router, hub or switch	40
Completing the hardware installation	40
3 Configuring the Matrix Switch for operation	41
Introduction	42
Configuration prerequisites	42
Initial configuration through the RS-232 control port	43
Connecting the DB9-RJ45 adapter with the included cable	43
Setting up the HyperTerminal (or similar program) session	44
Using a browser to complete Model 6511RC configuration	47
Displaying the Matrix Switch 6511RC web administration pages	47
Home page overview	49
Configuring the default gateway	51
Configuring the system clocking parameters	52
Module clocking mode	52
Module clocking source and fallback	53
Example 1	53
Example 2	54
Configuring the SDH circuit parameters	54
Accessing the SDH circuit parameters	55
Configuring the SDH physical interface type	56
Configuring the SDH interface parameters	56

4

Image 4

Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents Industry Canada Notice FCC Part 68 Acta StatementFacility Service Network Interface Code Connection CE NoticeAudience StructureTypographical conventions used in this document PrecautionsGeneral conventions Mouse conventions About this guide Chapter contents IntroductionModel 6511RC Matrix Switch overview Model 6511RC Matrix Switch front bladeModel 6511RC Matrix Switch major functions and interfaces Hardware overview Model 6511RCT rear bladeModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront chassis architectures ForeFront Model 6476 6U cPCI chassisForeFront Model 6676 9U chassis Model 6676 chassis, front viewMatrix Switch functionality TDM mapping and aggregationTDM bus architecture STM-1 link architectureMatrix Switch TDM capacity Matrix Switch Ethernet SwitchingManagement Services ManagementManagement Interfaces Management ApproachMatrix Switch Interfaces WAN InterfacesMid-Plane Interfaces LAN InterfaceCentral processing unit Power systemSystem timing Temperature Physical dimensionsLED Indicators AltitudeRear-panel LED indicators Approvals Etsi CTR EMCApprovals Hardware installation Verifying that the ForeFront chassis is properly installed Unpacking the Model 6511RC Matrix SwitchIntroduction Verifying correct cover plate installation Verfying correct electrical groundingMatrix Switch hardware installation Alignment/ESD pin and card handleInstalling the network cables Matrix Switch front blade network interface portsConnecting the front-panel Ethernet LAN port Ethernet RJ-45 pin and signal definitions for Matrix SwitchConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors Connecting the rear-panel Ethernet WAN/management ports BNC coaxial cable connectorsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page overview Home page window panesOperator Actions buttons Configuring the default gateway IP OverviewConfiguring the system clocking parameters Module clocking modeModule clocking source and fallback An internal oscillator STM-1 portConfiguring the SDH circuit parameters System Clocking Configuration page, exampleAccessing the SDH circuit parameters SDH Overview web managementConfiguring the SDH physical interface type Configuring the SDH interface parametersConfiguring the SDH path trace parameters SDH Path Trace parametersConfiguring DS0 idle codes Accessing the idle code configuration E1 LinkDefining the DS0 idle code configuration Selecting the SDH mapping pathSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings Defining DS0 mappings using E1 port format DS0 Mapping OverviewExamples for configuring DS0 mappings Solution Solution Solution Defining DS0 mappings using TU format DS0 Mapping Overview page with TU format selectedE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution Saving your configuration RC HomeBacking up your configuration parameters Import/ExportBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown Activating the Model 6511RC De-activating the Model 6511RCTroubleshooting and maintenance Troubleshooting during initial deployment Cited in section De-activating the Model 6511RC onGeneral fault analysis PowerCLK Enet Matrix Switch test tools Loopback test modes for the STM-1 portMatrix Switch TDM mapping architecture Facility Loop sonetFacilityLoop1SDH Configuration page with sonetFacilityLoop1 selected Terminal loop sonetTerminalLoop2SDH Configuration page with sonetTerminalLoop2 selected Other Loop sonetOtherLoop3 SDH section trace and path traceSections and paths Section traceSection Trace parameters on the SDH Configuration Path tracePath Trace parameters on the SDH Configuration Number of paths per framePeriodic maintenance MaintenanceExporting the current Model 6511RC configuration CalibrationMaintenance Maintenance Removing the defective Model 6511RC Installing the replacement Model 6511RC Importing a saved configurationCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditRMA numbers Return for credit policyShipping instructions Contacting Patton for assistance 104