Patton electronic 6511RC user manual Connecting the rear-panel STM-1 WAN port to an SDH network

Page 37

Model 6511RC User Manual	2 • Hardware installation

Connecting the front-panelEIA-561RS-232 configuration port (DCE configured) Install the supplied RJ-45-to-RJ-45 cable with the DB9-RJ45 adapter between the Matrix Switch RS-232 port (see figure 13 on page 35) and an open serial port on your computer. If you need to assemble your own cable, refer to the pinout diagram in figure 17.

Figure 17. RJ-45 pin and signal definitions for Matrix Switch CONFIG port

Connecting the rear-panel STM-1 WAN port to an SDH network

The Matrix Switch offers two types of STM-1 interfaces—optical and electrical—presented on the rear panel of the rear blade. Optical interfaces connect to fiber-optic network cables, while the electrical interfaces connect to coaxial network cables. The rear-blade connectors must match the type of network cables and connectors used by the SDH network to which you will connect.

Connecting the STM-1 optical interface to fiber-optic network cables

The following versions of the Matrix Switch rear blade offer an optical interface for the STM-1 port

•Model 6511RC/M155/SC20

•Model /EBNC6511RC/M155/SC20

The designation SC20 in the model code denotes that an optical interface conforming to ITU specification G.957 and G.652 is present. The Matrix Switch presents the STM-1 optical interface on a pair of SC fiber- optic connectors, one for the transmiting (TX) and one for receiving (RX) signals (see figure 14 on page 35).

Note The wavelength of the laser signal is 1310 nanometers. The single- mode fiber-optic cable connecting the STM-1 WAN port to the SDH network must extend no farther than 12.4 miles (20 kilometers).

Installing the network cables

37

Image 37

Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents FCC Part 68 Acta Statement Industry Canada NoticeCE Notice Facility Service Network Interface Code ConnectionStructure AudienceTypographical conventions used in this document PrecautionsGeneral conventions Mouse conventions About this guide Introduction Chapter contentsModel 6511RC Matrix Switch front blade Model 6511RC Matrix Switch overviewModel 6511RC Matrix Switch major functions and interfaces Model 6511RCT rear blade Hardware overviewModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront Model 6476 6U cPCI chassis ForeFront chassis architecturesModel 6676 chassis, front view ForeFront Model 6676 9U chassisTDM mapping and aggregation Matrix Switch functionalitySTM-1 link architecture TDM bus architectureMatrix Switch Ethernet Switching Matrix Switch TDM capacityManagement Management ServicesManagement Interfaces Management ApproachWAN Interfaces Matrix Switch InterfacesMid-Plane Interfaces LAN InterfaceCentral processing unit Power systemSystem timing Physical dimensions TemperatureLED Indicators AltitudeRear-panel LED indicators Etsi CTR EMC ApprovalsApprovals Hardware installation Verifying that the ForeFront chassis is properly installed Unpacking the Model 6511RC Matrix SwitchIntroduction Verfying correct electrical grounding Verifying correct cover plate installationAlignment/ESD pin and card handle Matrix Switch hardware installationMatrix Switch front blade network interface ports Installing the network cablesEthernet RJ-45 pin and signal definitions for Matrix Switch Connecting the front-panel Ethernet LAN portConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors BNC coaxial cable connectors Connecting the rear-panel Ethernet WAN/management portsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page window panes Home page overviewOperator Actions buttons IP Overview Configuring the default gatewayModule clocking mode Configuring the system clocking parametersAn internal oscillator STM-1 port Module clocking source and fallbackSystem Clocking Configuration page, example Configuring the SDH circuit parametersSDH Overview web management Accessing the SDH circuit parametersConfiguring the SDH interface parameters Configuring the SDH physical interface typeSDH Path Trace parameters Configuring the SDH path trace parametersConfiguring DS0 idle codes E1 Link Accessing the idle code configurationSelecting the SDH mapping path Defining the DS0 idle code configurationSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings DS0 Mapping Overview Defining DS0 mappings using E1 port formatExamples for configuring DS0 mappings Solution Solution Solution DS0 Mapping Overview page with TU format selected Defining DS0 mappings using TU formatE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution RC Home Saving your configurationImport/Export Backing up your configuration parametersBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown De-activating the Model 6511RC Activating the Model 6511RCTroubleshooting and maintenance Cited in section De-activating the Model 6511RC on Troubleshooting during initial deploymentPower General fault analysisCLK Enet Loopback test modes for the STM-1 port Matrix Switch test toolsFacility Loop sonetFacilityLoop1 Matrix Switch TDM mapping architectureTerminal loop sonetTerminalLoop2 SDH Configuration page with sonetFacilityLoop1 selectedSDH Configuration page with sonetTerminalLoop2 selected SDH section trace and path trace Other Loop sonetOtherLoop3Section trace Sections and pathsPath trace Section Trace parameters on the SDH ConfigurationNumber of paths per frame Path Trace parameters on the SDH ConfigurationMaintenance Periodic maintenanceExporting the current Model 6511RC configuration CalibrationMaintenance Maintenance Removing the defective Model 6511RC Importing a saved configuration Installing the replacement Model 6511RCCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditRMA numbers Return for credit policyShipping instructions Contacting Patton for assistance 104