Patton electronic 6511RC user manual Solution

Page 66

3 • Configuring the Matrix Switch for operation

Model 6511RC User Manual

 

 

Example 1

Map E1 Port 1 received, timeslots 1-32 to H.110 Port 1 timeslots 1-32.

Map E1 Port 1 transmitted, timeslots 1-32 from H.110 Port 1 timeslots 33-64.

Solution:

1.Under E1 Number, select port1(1) from the drop-down menu (see figure 48).

2.Under E1 Slots, enter 1-32in the text box.

3.For toH110(5), under H.110 Number, select port1(1) from the drop-down menu.

4.For toH110(5), under H.110 slots, enter 1-32 in the text box.

5.For fromH110(5), under H.110 Number, select port1(1) from the drop-down menu.

6.For fromH110(5), under H.110 slots, enter 33-64 in the text box.

Figure 48. Define a mapping table for Example 1

7.Click the Define button.

8.Verify your new mapping appears in the Defined Mappings table (see figure 49).

Figure 49. Defined Mappings table for example 1

9.Examine the new mapping to verify that it was entered and recorded correctly. You have completed the DS0 mapping procedure for example 1.

66

Using a browser to complete Model 6511RC configuration

Image 66
Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents Industry Canada Notice FCC Part 68 Acta StatementFacility Service Network Interface Code Connection CE NoticeAudience StructurePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions About this guide Chapter contents IntroductionModel 6511RC Matrix Switch overview Model 6511RC Matrix Switch front bladeModel 6511RC Matrix Switch major functions and interfaces Hardware overview Model 6511RCT rear bladeModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront chassis architectures ForeFront Model 6476 6U cPCI chassisForeFront Model 6676 9U chassis Model 6676 chassis, front viewMatrix Switch functionality TDM mapping and aggregationTDM bus architecture STM-1 link architectureMatrix Switch TDM capacity Matrix Switch Ethernet SwitchingManagement Interfaces Management ServicesManagement Management ApproachMid-Plane Interfaces Matrix Switch InterfacesWAN Interfaces LAN InterfacePower system Central processing unitSystem timing LED Indicators TemperaturePhysical dimensions AltitudeRear-panel LED indicators Approvals Etsi CTR EMCApprovals Hardware installation Unpacking the Model 6511RC Matrix Switch Verifying that the ForeFront chassis is properly installedIntroduction Verifying correct cover plate installation Verfying correct electrical groundingMatrix Switch hardware installation Alignment/ESD pin and card handleInstalling the network cables Matrix Switch front blade network interface portsConnecting the front-panel Ethernet LAN port Ethernet RJ-45 pin and signal definitions for Matrix SwitchConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors Connecting the rear-panel Ethernet WAN/management ports BNC coaxial cable connectorsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Initial configuration through the RS-232 control port Connecting the DB9-RJ45 adapter with the included cableSetting up the HyperTerminal or similar program session Connection Description windowConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page overview Home page window panesOperator Actions buttons Configuring the default gateway IP OverviewConfiguring the system clocking parameters Module clocking modeModule clocking source and fallback An internal oscillator STM-1 portConfiguring the SDH circuit parameters System Clocking Configuration page, exampleAccessing the SDH circuit parameters SDH Overview web managementConfiguring the SDH physical interface type Configuring the SDH interface parametersConfiguring the SDH path trace parameters SDH Path Trace parametersConfiguring DS0 idle codes Accessing the idle code configuration E1 LinkDefining the DS0 idle code configuration Selecting the SDH mapping pathSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings Defining DS0 mappings using E1 port format DS0 Mapping OverviewExamples for configuring DS0 mappings Solution Solution Solution Defining DS0 mappings using TU format DS0 Mapping Overview page with TU format selectedE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution Saving your configuration RC HomeBacking up your configuration parameters Import/ExportBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown Activating the Model 6511RC De-activating the Model 6511RCTroubleshooting and maintenance Troubleshooting during initial deployment Cited in section De-activating the Model 6511RC onGeneral fault analysis PowerCLK Enet Matrix Switch test tools Loopback test modes for the STM-1 portMatrix Switch TDM mapping architecture Facility Loop sonetFacilityLoop1SDH Configuration page with sonetFacilityLoop1 selected Terminal loop sonetTerminalLoop2SDH Configuration page with sonetTerminalLoop2 selected Other Loop sonetOtherLoop3 SDH section trace and path traceSections and paths Section traceSection Trace parameters on the SDH Configuration Path tracePath Trace parameters on the SDH Configuration Number of paths per frameExporting the current Model 6511RC configuration Periodic maintenanceMaintenance CalibrationMaintenance Maintenance Removing the defective Model 6511RC Installing the replacement Model 6511RC Importing a saved configurationCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for creditReturn for credit policy RMA numbersShipping instructions Contacting Patton for assistance 104