Patton electronic 6511RC Configuring the SDH path trace parameters, SDH Path Trace parameters

Page 57

Model 6511RC User Manual

3 • Configuring the Matrix Switch for operation

 

 

ter applies. When the section trace message length is defined to be one byte, the Matrix Switch will ignore the value of Section Trace.

5.For Section Trace Msg Len, from the drop-down menu, select the value used by the SDH network your Matrix Switch is connected to: either 1, 16, or 64-byte trace messages.

6.For Section Trace J0 Byte enter the value your connected SDH network uses for the J0 byte in the SDH frame.

Note J0 applies only with 1-byteSection Trace Messages. For 16-byte and 64-byte trace messages, the trace message string applies and the value of J0 is ignored.

7.For SDH Payload Mapping, select the payload type corresponding to the way your connected SDH net- work maps the E1 payload into the SDH frame structure. Asynchronous E1 payload mapping is most common, so the factory default value on the Matrix Switch is stm1MappedAsynchE1(0). If your connected SDH network performs byte-synchronous E1 payload mapping, then select stm1MappedBytesynchE1(1) from the drop-down menu.

8.For Tx Payload Scramble, if your SDH network expects to receive a scrambled payload select SDHScram- bleEnable(1) from the drop-down menu, otherwise select sdhScrambleDisable(0).

9.For Rx Payload Scramble, if your SDH network transmits a scrambled payload select SDHScrambleEn- able(1) from the drop-down menu, otherwise select sdhScrambleDisable(0).

10.For SDH Mapping, select the type of AU corresponding to the SDH multiplexing path you desire. To multiplex seven TUG-2s into an AU-3, select au3Mapper(0) (the factory default) from the drop-down menu. To multiplex three TUG-3s into an AU-4, select au4Mapper(1).

11.Click the Modify button to save your work into operating memory (volatile DRAM) and activate the new parameter values.

Configuring the SDH path trace parameters

If you selected AU-4 mapping in the preceding procedure, the Matrix Switch will display one set of five parame- ters pertaining to Path 1. If you selected AU-3 mapping, the Matrix Switch will display three sets of five parame- ters each pertaining to Paths 1, 2, and 3. Do the following to define the values for the SDH path trace parameters:

1.If path trace is enabled in your connected SDH network, go to step 2. Otherwise, because path trace is disabled, in the SDH trace parameters table (see figure 40), for Path-1 Trace Monitor, select pathTraceDis- able(0) from the drop-down menu. Refer to section “Configuring DS0 idle codes” on page 58.

Figure 40. SDH Path Trace parameters

Using a browser to complete Model 6511RC configuration

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents FCC Part 68 Acta Statement Industry Canada NoticeCE Notice Facility Service Network Interface Code ConnectionStructure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions About this guide Introduction Chapter contentsModel 6511RC Matrix Switch front blade Model 6511RC Matrix Switch overviewModel 6511RC Matrix Switch major functions and interfaces Model 6511RCT rear blade Hardware overviewModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront Model 6476 6U cPCI chassis ForeFront chassis architecturesModel 6676 chassis, front view ForeFront Model 6676 9U chassisTDM mapping and aggregation Matrix Switch functionalitySTM-1 link architecture TDM bus architectureMatrix Switch Ethernet Switching Matrix Switch TDM capacityManagement Management ServicesManagement Interfaces Management ApproachWAN Interfaces Matrix Switch InterfacesMid-Plane Interfaces LAN InterfacePower system Central processing unitSystem timing Physical dimensions TemperatureLED Indicators AltitudeRear-panel LED indicators Etsi CTR EMC ApprovalsApprovals Hardware installation Unpacking the Model 6511RC Matrix Switch Verifying that the ForeFront chassis is properly installedIntroduction Verfying correct electrical grounding Verifying correct cover plate installationAlignment/ESD pin and card handle Matrix Switch hardware installationMatrix Switch front blade network interface ports Installing the network cablesEthernet RJ-45 pin and signal definitions for Matrix Switch Connecting the front-panel Ethernet LAN portConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors BNC coaxial cable connectors Connecting the rear-panel Ethernet WAN/management portsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page window panes Home page overviewOperator Actions buttons IP Overview Configuring the default gatewayModule clocking mode Configuring the system clocking parametersAn internal oscillator STM-1 port Module clocking source and fallback System Clocking Configuration page, example Configuring the SDH circuit parametersSDH Overview web management Accessing the SDH circuit parametersConfiguring the SDH interface parameters Configuring the SDH physical interface typeSDH Path Trace parameters Configuring the SDH path trace parametersConfiguring DS0 idle codes E1 Link Accessing the idle code configurationSelecting the SDH mapping path Defining the DS0 idle code configurationSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings DS0 Mapping Overview Defining DS0 mappings using E1 port formatExamples for configuring DS0 mappings Solution Solution Solution DS0 Mapping Overview page with TU format selected Defining DS0 mappings using TU formatE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution RC Home Saving your configurationImport/Export Backing up your configuration parametersBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown De-activating the Model 6511RC Activating the Model 6511RCTroubleshooting and maintenance Cited in section De-activating the Model 6511RC on Troubleshooting during initial deploymentPower General fault analysisCLK Enet Loopback test modes for the STM-1 port Matrix Switch test toolsFacility Loop sonetFacilityLoop1 Matrix Switch TDM mapping architectureTerminal loop sonetTerminalLoop2 SDH Configuration page with sonetFacilityLoop1 selectedSDH Configuration page with sonetTerminalLoop2 selected SDH section trace and path trace Other Loop sonetOtherLoop3Section trace Sections and pathsPath trace Section Trace parameters on the SDH ConfigurationNumber of paths per frame Path Trace parameters on the SDH ConfigurationMaintenance Periodic maintenanceExporting the current Model 6511RC configuration CalibrationMaintenance Maintenance Removing the defective Model 6511RC Importing a saved configuration Installing the replacement Model 6511RCCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditReturn for credit policy RMA numbersShipping instructions Contacting Patton for assistance 104
Top Page Image Contents