Patton electronic 6511RC user manual General fault analysis, Power

Page 83

Model 6511RC User Manual5 • Troubleshooting and maintenance

 

Table 5. Symptoms (Continued)

 

 

Problem

Corrective Action

 

 

SYSTEM LED (green) is

The Model 6511RC is not functioning properly.

not flashing

As soon as possible, force a module power cycle as follows:

 

 

1)Wearing an antistatic strap, simultaneously press both red buttons on the front-

 

panel handles of the 6511RC to unlock the handles and prepare the module for

 

removal.

 

2)Simultaneously press both black handles outward and away from the center of

 

the module to unseat the 6511RC from the mid-plane connectors.

 

3) Wait 10 seconds.

 

4)Holding the module by the two black handles, very carefully push the module

 

gently and firmly into the chassis until it is reseated against the midplane.

 

5)Press the black handle so that they click and lock closed.

 

Once the Matrix Switch has resumed operation re-inspect the SYSTEM LED. If the

 

SYSTEM LED does not begin flashing after completing the power-up cycle, contact

 

Patton Technical Support to determine if the Matrix Switch should be replaced.

 

 

General fault analysis

The following procedures outline steps you should follow when troubleshooting a Model 6511RC malfunction.

1.If possible, talk to the person who reported the problem and obtain a detailed description of the symp- toms. Create a written trouble report listing all the symptoms observed, including a complete description of the status for each LED indicator.

2.LED Status Indications and Recommended actions, table 6 provides information on interpreting LED status indicators along with recommended actions in response to each LED status indication. To correct the problem with your Matrix Switch, compare each LED status in your trouble report with the information in the table, and follow the recommend action for each LED.

Table 6. LED status indications and recommended actions

LED

Location

Color Status

Meaning

POWER

Front

panel

Green

On solid Power is being applied. No action recommended.

Flashing The 6511RC has detected a power failure on a power bus. There may be a problem with the CPCI power supply system such as a failed power supply module in the chassis. The Model 6511RC will function normally with one power supply.

Inspect the power supplies in the CPCI chassis to identify and replace the failed power supply module. If the POWER LED continues flashing when all chassis power supplies are functional, contact Patton Technical Sup- port to determine if the Matrix Switch should be replaced.

Off No input power is being applied. Verify that at least one chassis power supply module is installed in the chassis and functioning normally.

General fault analysis

83

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents FCC Part 68 Acta Statement Industry Canada NoticeCE Notice Facility Service Network Interface Code ConnectionStructure AudienceGeneral conventions PrecautionsTypographical conventions used in this document Mouse conventions About this guide Introduction Chapter contentsModel 6511RC Matrix Switch front blade Model 6511RC Matrix Switch overviewModel 6511RC Matrix Switch major functions and interfaces Model 6511RCT rear blade Hardware overviewModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront Model 6476 6U cPCI chassis ForeFront chassis architecturesModel 6676 chassis, front view ForeFront Model 6676 9U chassisTDM mapping and aggregation Matrix Switch functionalitySTM-1 link architecture TDM bus architectureMatrix Switch Ethernet Switching Matrix Switch TDM capacityManagement Approach Management ServicesManagement Management InterfacesLAN Interface Matrix Switch InterfacesWAN Interfaces Mid-Plane InterfacesSystem timing Power systemCentral processing unit Altitude TemperaturePhysical dimensions LED IndicatorsRear-panel LED indicators Etsi CTR EMC ApprovalsApprovals Hardware installation Introduction Unpacking the Model 6511RC Matrix SwitchVerifying that the ForeFront chassis is properly installed Verfying correct electrical grounding Verifying correct cover plate installationAlignment/ESD pin and card handle Matrix Switch hardware installationMatrix Switch front blade network interface ports Installing the network cablesEthernet RJ-45 pin and signal definitions for Matrix Switch Connecting the front-panel Ethernet LAN portConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors BNC coaxial cable connectors Connecting the rear-panel Ethernet WAN/management portsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page window panes Home page overviewOperator Actions buttons IP Overview Configuring the default gatewayModule clocking mode Configuring the system clocking parametersAn internal oscillator STM-1 port Module clocking source and fallbackSystem Clocking Configuration page, example Configuring the SDH circuit parametersSDH Overview web management Accessing the SDH circuit parametersConfiguring the SDH interface parameters Configuring the SDH physical interface typeSDH Path Trace parameters Configuring the SDH path trace parametersConfiguring DS0 idle codes E1 Link Accessing the idle code configurationSelecting the SDH mapping path Defining the DS0 idle code configurationSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings DS0 Mapping Overview Defining DS0 mappings using E1 port formatExamples for configuring DS0 mappings Solution Solution Solution DS0 Mapping Overview page with TU format selected Defining DS0 mappings using TU formatE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution RC Home Saving your configurationImport/Export Backing up your configuration parametersBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown De-activating the Model 6511RC Activating the Model 6511RCTroubleshooting and maintenance Cited in section De-activating the Model 6511RC on Troubleshooting during initial deploymentPower General fault analysisCLK Enet Loopback test modes for the STM-1 port Matrix Switch test toolsFacility Loop sonetFacilityLoop1 Matrix Switch TDM mapping architectureTerminal loop sonetTerminalLoop2 SDH Configuration page with sonetFacilityLoop1 selectedSDH Configuration page with sonetTerminalLoop2 selected SDH section trace and path trace Other Loop sonetOtherLoop3Section trace Sections and pathsPath trace Section Trace parameters on the SDH ConfigurationNumber of paths per frame Path Trace parameters on the SDH ConfigurationCalibration Periodic maintenanceMaintenance Exporting the current Model 6511RC configurationMaintenance Maintenance Removing the defective Model 6511RC Importing a saved configuration Installing the replacement Model 6511RCCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Returns for credit Warranty coverageOut-of-warranty service Contact informationShipping instructions Return for credit policyRMA numbers Contacting Patton for assistance 104
Top Page Image Contents