Patton electronic 6511RC user manual Defining DS0 mappings using TU format

Page 69

Model 6511RC User Manual	3 • Configuring the Matrix Switch for operation

Defining DS0 mappings using TU format

Experienced SDH engineers with a solid understanding of STM-1 architecture will most likely prefer to use TU format to define DS0 mappings. To define a DS0 mapping using TU format, do the following:

1.On the 6511RC Configuration Menu (see figure 27 on page 48), click the DS0 Mapping hyperlink to dis- play the DS0 Mapping Overview page (see figure 54).

2.For the Display Option parameter, verify that displayLongForm(0) is selected from the drop-down menu.

3.For the E1 Input Format parameter, select tuFormat(0) from the dropdown menu.

4.Click the Modify button to save changes.

Figure 54. DS0 Mapping Overview page with TU format selected

Using a browser to complete Model 6511RC configuration

69

Image 69

Contents Matrix Switch Patton Electronics Company, Inc Contents Hardware installation Operation and shutdown Contents FCC Part 68 Acta Statement Industry Canada NoticeCE Notice Facility Service Network Interface Code ConnectionStructure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions About this guide Introduction Chapter contentsModel 6511RC Matrix Switch front blade Model 6511RC Matrix Switch overviewModel 6511RC Matrix Switch major functions and interfaces Model 6511RCT rear blade Hardware overviewModel 6511RC front panel LEDs and ports Model 6511RCT rear entry car front panel LEDs and ports ForeFront Model 6476 6U cPCI chassis ForeFront chassis architecturesModel 6676 chassis, front view ForeFront Model 6676 9U chassisTDM mapping and aggregation Matrix Switch functionalitySTM-1 link architecture TDM bus architectureMatrix Switch Ethernet Switching Matrix Switch TDM capacityManagement Management ServicesManagement Interfaces Management ApproachWAN Interfaces Matrix Switch InterfacesMid-Plane Interfaces LAN InterfacePower system Central processing unitSystem timing Physical dimensions TemperatureLED Indicators AltitudeRear-panel LED indicators Etsi CTR EMC ApprovalsApprovals Hardware installation Unpacking the Model 6511RC Matrix Switch Verifying that the ForeFront chassis is properly installedIntroduction Verfying correct electrical grounding Verifying correct cover plate installationAlignment/ESD pin and card handle Matrix Switch hardware installationMatrix Switch front blade network interface ports Installing the network cablesEthernet RJ-45 pin and signal definitions for Matrix Switch Connecting the front-panel Ethernet LAN portConnecting the rear-panel STM-1 WAN port to an SDH network Fiber-optic SC cable connectors BNC coaxial cable connectors Connecting the rear-panel Ethernet WAN/management portsCompleting the hardware installation Configuring the Matrix Switch for Operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control portConnection Description window Setting up the HyperTerminal or similar program sessionConfigure your COM port settings as shown in , then click OK Login window Using a browser to complete Model 6511RC configuration 3069RC Configuration Menu home page will appear see figure Home page window panes Home page overviewOperator Actions buttons IP Overview Configuring the default gatewayModule clocking mode Configuring the system clocking parametersAn internal oscillator STM-1 port Module clocking source and fallbackSystem Clocking Configuration page, example Configuring the SDH circuit parametersSDH Overview web management Accessing the SDH circuit parametersConfiguring the SDH interface parameters Configuring the SDH physical interface typeSDH Path Trace parameters Configuring the SDH path trace parametersConfiguring DS0 idle codes E1 Link Accessing the idle code configurationSelecting the SDH mapping path Defining the DS0 idle code configurationSDH Overview Defining DS0 mappings Following sections describe how to define DS0 mappings DS0 Mapping Overview Defining DS0 mappings using E1 port formatExamples for configuring DS0 mappings Solution Solution Solution DS0 Mapping Overview page with TU format selected Defining DS0 mappings using TU formatE1 port numbers located within the STM-1 frame structure Configuring the Matrix Switch for operation Solution Solution RC Home Saving your configurationImport/Export Backing up your configuration parametersBacking up the configuration store in flash memory Completing the installation Completing the installation Operation and shutdown De-activating the Model 6511RC Activating the Model 6511RCTroubleshooting and maintenance Cited in section De-activating the Model 6511RC on Troubleshooting during initial deploymentPower General fault analysisCLK Enet Loopback test modes for the STM-1 port Matrix Switch test toolsFacility Loop sonetFacilityLoop1 Matrix Switch TDM mapping architectureTerminal loop sonetTerminalLoop2 SDH Configuration page with sonetFacilityLoop1 selectedSDH Configuration page with sonetTerminalLoop2 selected SDH section trace and path trace Other Loop sonetOtherLoop3Section trace Sections and pathsPath trace Section Trace parameters on the SDH ConfigurationNumber of paths per frame Path Trace parameters on the SDH ConfigurationMaintenance Periodic maintenanceExporting the current Model 6511RC configuration CalibrationMaintenance Maintenance Removing the defective Model 6511RC Importing a saved configuration Installing the replacement Model 6511RCCompleting the installation Troubleshooting and maintenance 100 Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for creditReturn for credit policy RMA numbersShipping instructions Contacting Patton for assistance 104