Peavey CS 800H manual

Page 31

CS® 800H

SPECIFICATIONS

Rated output power (120 VAC, 60 Hz): Bridge mode, mono:

4 Ohms: 800 W @ 1 kHz, <0.1%

THD

8 Ohms: 650 W @ 1 kHz, <0.1%

THD

Stereo mode, both channels driven:

2 Ohms: 400 W per channel

1 kHz, <0.05% THD

4 Ohms: 325 W per channel

1 kHz, <0.05% THD

8 Ohms: 225 W per channel

1 kHz, <0.05% THD

Minimum load impedance:

Stereo mode: 2 Ohms

Bridge mode: 4 Ohms

Frequency response:

10 Hz to 50 kHz; +0‚ -1 dB, 4 Ohms @ 1 W

Power bandwidth:

15 Hz to 50 kHz; +0‚ -1 dB @ rated, 4 Ohms

Total harmonic distortion:

Stereo mode, both channels driven <0.1% @ 500 W per channel from 20 Hz to 20 kHz

Voltage gain:

Input attenuator set @ FCW 31 dB, stereo mode, 4 Ohms, 1 kHz

38 dB, bridge mode, 8 Ohms,

1 kHz

Crosstalk:

>-75 dB @ 1 kHz @ rated power, 8 Ohms

Crossover:

Fourth order state variable filters:

24dB/Octave Frequency range:

40Hz to 300 Hz

Hum and noise:

Stereo mode, both channels driven below rated output power,

4 Ohms,

>100 dB (30 kHz BW, unweighted)

Slew rate:

Stereo mode, each channel >20V/us

Damping factor:

>250 @ 8 Ohms, 20 Hz to 1 kHz

Phase response:

Stereo mode, 4 Ohms @ rated power

20 Hz leading waveform: <-16.5˚

20 kHz lagging waveform: <+17.5˚

Input sensitivity:

Input attenuator set @ FCW

1.0V @ rated power, 4 Ohms, 1 kHz

Input impedance:

Input attenuator set @ FCW 20 k Ohms, balanced

Cooling:

One front panel, temperature dependant, variable speed DC fan

Controls:

Two front panel attenuators‚ rear panel mode switch‚ rear panel DDT defeat switch, function switch per channel, adjustable low cut filter per channel, low cut filter bypass switch per channel, adjustable subwoofer crossover per channel

Indicator LEDs:

Two DDT, two active status, two DC protect, two over-temperature, two ten-segment signal displays

Protection:

Clipping, short-circuit, thermal overload, DC, turn-on burst, incorrect loads

Connectors:

Combination XLR and 1/4"

(6.3 mm) phone input, Speakon® and binding post speaker output 1/4" (6.3 mm), high pass or full range patch connector per channel, 1/4" (6.3 mm) low pass patch connector per channel, 15 amp IEC mains connectors

Construction:

16 ga. steel with cast aluminum front panel and cast handles

Dimensions (H x W x D):

3.5" x 19" 17.5"

(8.9 cm x 48.3 cm x 44.5 cm)

Net weight:

33.4 lbs (15.2 kg)

Gross Weight:

45.5 lbs (20.6 kg)

2 Ohms stereo mode and 4 Ohms bridge mode power is time limited by magnetic circuit breaker

31

Image 31
Contents CS800H Operations Manual Page Sound Level dBA, Slow Response Important Safety InstructionsCooling Requirements CS 800H Power AmplifierUnpacking MountingR E U G E A R T Operating PrecautionsStereo Connecting InputsConnecting Outputs Connecting PowerInput Attenuators AC Power Switch/Circuit BreakerFront Panel Indicators Signal LEDAir Intake Vent Mode Select SwitchDDT Switch Active LEDLow Cut Adjustment Knob Crossover Adjustment KnobAmp Function Switch Low Cut SwitchDDT Amplifier Maintenance and User Responsibility RampUp Signal ControlSpeaker Protection Diagram Glossary of Terms Setup Instructions To Stereo Bi-amp Hookup Diagram CS 800H Auspacken CS 800H VerstärkerMontage Sicherheitshinweise für den Betrieb KühlanforderungenAnschluss der Ausgänge Anschluss der EingängeBridged-Modus NetzanschlussTEMP-LED SIGNAL-LEDACTIVE-LED Low-Cut-Schalter KanaleingangFrequenzweichen-Einstellknopf Amp-Function-SchalterErmittlung und Begrenzung von Verzerrung DDT Speakon-AusgangssteckerAnschlussklemmen-Ausgangsstecker Stecker des WechselstromnetzkabelsEinschalt-/Ausschaltschutz RampUp-SignalregelungKurzschluss Schutz vor GleichspannungWartung des Verstärkers und Verantwortung des Nutzers Erklärung der Begriffe Setup-Anweisungen Mono-Biamp-Betrieb Subwoofer und Mid/High-Box CS 800H Desempaque Amplificador de Poder CS 800HInstalación Precauciones de Operación Requisitos de enfriamientoConectando Salidas Conectando EntradasMono Puente Conectando CorrienteEstéreo ParaleloLED de Señal Interruptor de Corriente/Breaker de CircuitoAtenuadores de Entrada Indicadores del Panel FrontalLED Activo Interruptor de Función del Amplificador Interruptor DDTEntrada de Canal Perilla de ajuste del CrossoverConectador e corriente CA Salida de LOW PassConectador de salida Speakon Conectores de salida de poste binding postCortos Circuitos Limitación de Detección de DistorsiónSensibilidad de Impedancia LFC Protección TérmicaControl de señal RampUp Protección de Encendido/ApagadoProtección de Parlantes Glosario de Términos Operación de Dos Canales Paralelos Rango Completo Operación Mono Bi-Amp CS 800H Refroidissement InstallationAmplificateurs de Puissance CS 800H DéballagePrécautions d’Utilisation Stéréo Connecter les entrées de votre unité InputsConnecter les sorties de votre unité Outputs Alimentation ElectriqueIndicateurs du Panneau Avant Signal LEDDDT LED Temp LEDActive LED Protection Thermique Limite de Détection de DistortionProtection contre le Courant Continu Protection des Haut-Parleurs Maintenance et Responsabilité d’UtilisateurProtection de Mise Sous/Hors Tension Système RampUp contrôle de montée en puissanceGlossaire Setup-Anweisungen To Stereo CS 800H Page Page Product Category Peavey Electronics Corporation Limited Warranty80304955