Peavey CS 800H manual

Page 56

CS® 800H

SPECIFICATIONS

Rated output power (120 VAC, 60 Hz): Bridge mode, mono:

4 Ohms: 800 W @ 1 kHz, <0.1%

THD

8 Ohms: 650 W @ 1 kHz, <0.1%

THD

Stereo mode, both channels driven:

2 Ohms: 400 W per channel

1 kHz, <0.05% THD

4 Ohms: 325 W per channel

1 kHz, <0.05% THD

8 Ohms: 225 W per channel

1 kHz, <0.05% THD

Minimum load impedance:

Stereo mode: 2 Ohms

Bridge mode: 4 Ohms

Frequency response:

10 Hz to 50 kHz; +0‚ -1 dB, 4 Ohms @ 1 W

Power bandwidth:

15 Hz to 50 kHz; +0‚ -1 dB @ rated, 4 Ohms

Total harmonic distortion:

Stereo mode, both channels driven <0.1% @ 500 W per channel from 20 Hz to 20 kHz

Voltage gain:

Input attenuator set @ FCW 31 dB, stereo mode, 4 Ohms, 1 kHz

38 dB, bridge mode, 8 Ohms,

1 kHz

Crosstalk:

>-75 dB @ 1 kHz @ rated power, 8 Ohms

Crossover:

Fourth order state variable filters:

24dB/Octave Frequency range:

40Hz to 300 Hz

Hum and noise:

Stereo mode, both channels driven below rated output power,

4 Ohms,

>100 dB (30 kHz BW, unweighted)

Slew rate:

Stereo mode, each channel >20V/us

Damping factor:

>250 @ 8 Ohms, 20 Hz to 1 kHz

Phase response:

Stereo mode, 4 Ohms @ rated power

20 Hz leading waveform: <-16.5˚

20 kHz lagging waveform: <+17.5˚

Input sensitivity:

Input attenuator set @ FCW

1.0V @ rated power, 4 Ohms, 1 kHz

Input impedance:

Input attenuator set @ FCW 20 k Ohms, balanced

Cooling:

One front panel, temperature dependant, variable speed DC fan

Controls:

Two front panel attenuators‚ rear panel mode switch‚ rear panel DDT defeat switch, function switch per channel, adjustable low cut filter per channel, low cut filter bypass switch per channel, adjustable subwoofer crossover per channel

Indicator LEDs:

Two DDT, two active status, two DC protect, two over-temperature, two ten-segment signal displays

Protection:

Clipping, short-circuit, thermal overload, DC, turn-on burst, incorrect loads

Connectors:

Combination XLR and 1/4"

(6.3 mm) phone input, Speakon® and binding post speaker output 1/4" (6.3 mm), high pass or full range patch connector per channel, 1/4" (6.3 mm) low pass patch connector per channel, 15 amp IEC mains connectors

Construction:

16 ga. steel with cast aluminum front panel and cast handles

Dimensions (H x W x D):

3.5" x 19" 17.5"

(8.9 cm x 48.3 cm x 44.5 cm)

Net weight:

33.4 lbs (15.2 kg)

Gross Weight:

45.5 lbs (20.6 kg)

2 Ohms stereo mode and 4 Ohms bridge mode power is time limited by magnetic circuit breaker

56

Image 56
Contents CS800H Operations Manual Page Important Safety Instructions Sound Level dBA, Slow ResponseCS 800H Power Amplifier UnpackingMounting Cooling RequirementsOperating Precautions R E U G E A R TConnecting Inputs Connecting OutputsConnecting Power StereoAC Power Switch/Circuit Breaker Front Panel IndicatorsSignal LED Input AttenuatorsMode Select Switch DDT SwitchActive LED Air Intake VentCrossover Adjustment Knob Amp Function SwitchLow Cut Switch Low Cut Adjustment KnobDDT Speaker Protection RampUp Signal ControlAmplifier Maintenance and User Responsibility Diagram Glossary of Terms Setup Instructions To Stereo Bi-amp Hookup Diagram CS 800H Montage CS 800H VerstärkerAuspacken Kühlanforderungen Sicherheitshinweise für den BetriebAnschluss der Eingänge Anschluss der AusgängeNetzanschluss Bridged-ModusSIGNAL-LED TEMP-LEDACTIVE-LED Kanaleingang Frequenzweichen-EinstellknopfAmp-Function-Schalter Low-Cut-SchalterSpeakon-Ausgangsstecker Anschlussklemmen-AusgangssteckerStecker des Wechselstromnetzkabels Ermittlung und Begrenzung von Verzerrung DDTRampUp-Signalregelung KurzschlussSchutz vor Gleichspannung Einschalt-/AusschaltschutzWartung des Verstärkers und Verantwortung des Nutzers Erklärung der Begriffe Setup-Anweisungen Mono-Biamp-Betrieb Subwoofer und Mid/High-Box CS 800H Instalación Amplificador de Poder CS 800HDesempaque Requisitos de enfriamiento Precauciones de OperaciónConectando Entradas Conectando SalidasConectando Corriente EstéreoParalelo Mono PuenteInterruptor de Corriente/Breaker de Circuito Atenuadores de EntradaIndicadores del Panel Frontal LED de SeñalLED Activo Interruptor DDT Entrada de CanalPerilla de ajuste del Crossover Interruptor de Función del AmplificadorSalida de LOW Pass Conectador de salida SpeakonConectores de salida de poste binding post Conectador e corriente CALimitación de Detección de Distorsión Sensibilidad de Impedancia LFCProtección Térmica Cortos CircuitosProtección de Parlantes Protección de Encendido/ApagadoControl de señal RampUp Glosario de Términos Operación de Dos Canales Paralelos Rango Completo Operación Mono Bi-Amp CS 800H Installation Amplificateurs de Puissance CS 800HDéballage RefroidissementPrécautions d’Utilisation Connecter les entrées de votre unité Inputs Connecter les sorties de votre unité OutputsAlimentation Electrique StéréoSignal LED Indicateurs du Panneau AvantActive LED Temp LEDDDT LED Protection contre le Courant Continu Limite de Détection de DistortionProtection Thermique Maintenance et Responsabilité d’Utilisateur Protection de Mise Sous/Hors TensionSystème RampUp contrôle de montée en puissance Protection des Haut-ParleursGlossaire Setup-Anweisungen To Stereo CS 800H Page Page Peavey Electronics Corporation Limited Warranty Product Category80304955