Peavey CS 800H manual

Page 45

CS® 800H

SPECIFICATIONS

Rated output power (120 VAC, 60 Hz): Bridge mode, mono:

4 Ohms: 800 W @ 1 kHz, <0.1%

THD

8 Ohms: 650 W @ 1 kHz, <0.1%

THD

Stereo mode, both channels driven:

2 Ohms: 400 W per channel

1 kHz, <0.05% THD

4 Ohms: 325 W per channel

1 kHz, <0.05% THD

8 Ohms: 225 W per channel

1 kHz, <0.05% THD

Minimum load impedance:

Stereo mode: 2 Ohms

Bridge mode: 4 Ohms

Frequency response:

10 Hz to 50 kHz; +0‚ -1 dB, 4 Ohms @ 1 W

Power bandwidth:

15 Hz to 50 kHz; +0‚ -1 dB @ rated, 4 Ohms

Total harmonic distortion:

Stereo mode, both channels driven <0.1% @ 500 W per channel from 20 Hz to 20 kHz

Voltage gain:

Input attenuator set @ FCW 31 dB, stereo mode, 4 Ohms, 1 kHz

38 dB, bridge mode, 8 Ohms,

1 kHz

Crosstalk:

>-75 dB @ 1 kHz @ rated power, 8 Ohms

Crossover:

Fourth order state variable filters:

24dB/Octave Frequency range:

40Hz to 300 Hz

Hum and noise:

Stereo mode, both channels driven below rated output power,

4 Ohms,

>100 dB (30 kHz BW, unweighted)

Slew rate:

Stereo mode, each channel >20V/us

Damping factor:

>250 @ 8 Ohms, 20 Hz to 1 kHz

Phase response:

Stereo mode, 4 Ohms @ rated power

20 Hz leading waveform: <-16.5˚

20 kHz lagging waveform: <+17.5˚

Input sensitivity:

Input attenuator set @ FCW

1.0V @ rated power, 4 Ohms, 1 kHz

Input impedance:

Input attenuator set @ FCW 20 k Ohms, balanced

Cooling:

One front panel, temperature dependant, variable speed DC fan

Controls:

Two front panel attenuators‚ rear panel mode switch‚ rear panel DDT defeat switch, function switch per channel, adjustable low cut filter per channel, low cut filter bypass switch per channel, adjustable subwoofer crossover per channel

Indicator LEDs:

Two DDT, two active status, two DC protect, two over-temperature, two ten-segment signal displays

Protection:

Clipping, short-circuit, thermal overload, DC, turn-on burst, incorrect loads

Connectors:

Combination XLR and 1/4"

(6.3 mm) phone input, Speakon® and binding post speaker output 1/4" (6.3 mm), high pass or full range patch connector per channel, 1/4" (6.3 mm) low pass patch connector per channel, 15 amp IEC mains connectors

Construction:

16 ga. steel with cast aluminum front panel and cast handles

Dimensions (H x W x D):

3.5" x 19" 17.5"

(8.9 cm x 48.3 cm x 44.5 cm)

Net weight:

33.4 lbs (15.2 kg)

Gross Weight:

45.5 lbs (20.6 kg)

2 Ohms stereo mode and 4 Ohms bridge mode power is time limited by magnetic circuit breaker

45

Image 45
Contents CS800H Operations Manual Page Sound Level dBA, Slow Response Important Safety InstructionsUnpacking CS 800H Power AmplifierMounting Cooling RequirementsR E U G E A R T Operating PrecautionsConnecting Outputs Connecting InputsConnecting Power StereoFront Panel Indicators AC Power Switch/Circuit BreakerSignal LED Input AttenuatorsDDT Switch Mode Select SwitchActive LED Air Intake VentAmp Function Switch Crossover Adjustment KnobLow Cut Switch Low Cut Adjustment KnobDDT RampUp Signal Control Amplifier Maintenance and User ResponsibilitySpeaker Protection Diagram Glossary of Terms Setup Instructions To Stereo Bi-amp Hookup Diagram CS 800H CS 800H Verstärker AuspackenMontage Sicherheitshinweise für den Betrieb KühlanforderungenAnschluss der Ausgänge Anschluss der EingängeBridged-Modus NetzanschlussTEMP-LED SIGNAL-LEDACTIVE-LED Frequenzweichen-Einstellknopf KanaleingangAmp-Function-Schalter Low-Cut-SchalterAnschlussklemmen-Ausgangsstecker Speakon-AusgangssteckerStecker des Wechselstromnetzkabels Ermittlung und Begrenzung von Verzerrung DDTKurzschluss RampUp-SignalregelungSchutz vor Gleichspannung Einschalt-/AusschaltschutzWartung des Verstärkers und Verantwortung des Nutzers Erklärung der Begriffe Setup-Anweisungen Mono-Biamp-Betrieb Subwoofer und Mid/High-Box CS 800H Amplificador de Poder CS 800H DesempaqueInstalación Precauciones de Operación Requisitos de enfriamientoConectando Salidas Conectando EntradasEstéreo Conectando CorrienteParalelo Mono PuenteAtenuadores de Entrada Interruptor de Corriente/Breaker de CircuitoIndicadores del Panel Frontal LED de SeñalLED Activo Entrada de Canal Interruptor DDTPerilla de ajuste del Crossover Interruptor de Función del AmplificadorConectador de salida Speakon Salida de LOW PassConectores de salida de poste binding post Conectador e corriente CASensibilidad de Impedancia LFC Limitación de Detección de DistorsiónProtección Térmica Cortos CircuitosProtección de Encendido/Apagado Control de señal RampUpProtección de Parlantes Glosario de Términos Operación de Dos Canales Paralelos Rango Completo Operación Mono Bi-Amp CS 800H Amplificateurs de Puissance CS 800H InstallationDéballage RefroidissementPrécautions d’Utilisation Connecter les sorties de votre unité Outputs Connecter les entrées de votre unité InputsAlimentation Electrique StéréoIndicateurs du Panneau Avant Signal LEDTemp LED DDT LEDActive LED Limite de Détection de Distortion Protection ThermiqueProtection contre le Courant Continu Protection de Mise Sous/Hors Tension Maintenance et Responsabilité d’UtilisateurSystème RampUp contrôle de montée en puissance Protection des Haut-ParleursGlossaire Setup-Anweisungen To Stereo CS 800H Page Page Product Category Peavey Electronics Corporation Limited Warranty80304955