Kramer Electronics PL-150 Kramer Protocol, Protocol 3000 Syntax, Host message format, Cr Lf

Page 40

Kramer Protocol 3000

10Kramer Protocol 3000

The Ethernet/USB/RS-232/RS-4851communication protocol2 lets you control the machine from any standard terminal software (for example, Windows® HyperTerminal Application).

10.1Protocol 3000 Syntax

Host message format:

Start	Address (optional)	Body			Delimiter
#	Destination_id@	message
#	Destination_id@	message		CR

Simple command (commands string with only one command without addressing):

start	body	delimiter
#	Command SP Parameter_1,Parameter_2,…	CR

Commands string (formal syntax with commands concatenation and addressing):

Start

Address

Body

Delimiter

#

Destination_id@

Command_1 Parameter1_1,Parameter1_2,…

CR

Command_2 Parameter2_1,Parameter2_2,…

Command_3 Parameter3_1,Parameter3_2,……

Device message format:

Start

Address (optional)

Body

Delimiter

~

Sender_id@

message

CR LF

Device long response (Echoing command):

Start

Address (optional)

Body

Delimiter

~

Sender_id@

command SP [param1 ,param2 …]

CR LF

result

CR = Carriage return (ASCII 13 = 0x0D)

LF = Line feed (ASCII 10 = 0x0A)

SP = Space (ASCII 32 = 0x20)

1 RS-232/RS-485 use a data rate of 115200 baud, with no parity, 8 data bits, and 1 stop bit

2 Not available at the time of printing. Refer to our Web site at http://www.kramerelectronics.com for details

36	KRAMER: SIMPLE CREATIVE TECHNOLOGY

Image 40

Contents Model Contents Figures Instruction Codes43Tables Introduction Getting StartedP3K Wizard Software Quick StartGetting Started Overview EthernetYour PL-50 Power Controller Monitor Your PL-50 Power Controller MonitorPL-50 Power Controller Monitor Front Panel PL-50 Power Controller Monitor Features Feature FunctionInstalling in a Rack Before Installing in a RackConnecting the PL-50 Power Controller Monitor Connecting the PL-50Connecting the Relays Controlling the PL-50 via the Ethernet PortRight-click Local Area Connection Properties Local Area Connection Properties window appearsConnecting via a Straight-Through Cable Click the Connect button Connect screen appears as follows Upload Main ScreenIf required, make changes and click Save. If not, click Exit Controlling via the Embedded Web Pages Following window appearsRunning the Application Panel Screen Scheduler Screen Features Scheduler ScreenHelp BOX Define the Channel Settings screen Channel Settings Screen FeaturesAlerts Screen Features Define the Alerts screenSetting the Alarms Define the Power Measurement screen Power Measurement Screen FeaturesPower ON/OFF Order Screen This page lets you set the power on and OFF order and delay Configurations Screen Enable Security System Security System EnabledSecurity System Operating Your PL-50 Power Controller Monitor DIP-switch SettingsDIP-switch Definitions Calibrating via the Front Panel ButtonsOperating Your PL-50 Power Controller Monitor Flash Memory Upgrade Upgrading the FirmwareClick the Connect button Connect Window appears see Figure Upload ScreenMachine is now connected Connection Time Out MessageUpload Connected Upload Progress When the update is finished, the restart message appears Restart MessageTechnical Specifications Includes the technical specificationsTechnical Specifications1 of the PL-50 Changing the Device ParametersKramer Protocol Protocol 3000 SyntaxHost message format CR LFCommand Terms CommandCommon Commands Factory NameNAME? NAME? NameResult and Error Codes Security CommandsNetwork Setting Commands These commands are used by network devices running ProtocolNET-DHCP NET-DHCP?NET-GATE NET-GATE?Instruction Codes ALARM-OFF ALARM-ONALARM-ON Result ALARM-ON? ALARM-START-ASSwitch MES-MODELVL SCHED?SWITCH? SWITCH-ORDERSWITCH-ORDER-DELAY SWITCH-ORDER-DELAY?Limited Warranty 2900-000576 REV