Kramer Electronics PL-150 user manual Mes-Mode, Lvl, Sched?, Switch

Page 49

Kramer Protocol 3000

ALERT-REG?

Cmd Short

Description

Command Type

Permission

Query Alert Registration

PL-50

User

Usage:

Syntax

Response

ALERT-REG?

ALERT-REG?

CHNL

CHNL

,EVENT

,ACTION

= (1-5)

CHNL

EVENT

= (TO_OFF,TO_ON,TO_FULL,TO_STBY,TO_NONE,ANY_CHANGE)

ACTION

= (NO_ALERT,ALARM, ALL_ALERTS)

MEASURE

Cmd Short

Description

Command Type

Permission

Device notification

PL-50

Usage:

Syntax

Response

MEASURE

,

CHNL

MES-MODE

Query the "full" and "standby" LED status. (device will report to all protocol ports on any change)

LVL

= (0 = no LEDs, 1 = standby LED on, 2 = full LED on)

CHNL

= (1-5)

MES-MODE

= (0=MEASURE_START, 1 = MEASURE_DONE, 2 = MEASURE_TIMEOUT)

PWR-LVL?

Cmd Short

Description

Command Type

Permission

Query Power level

PL-50

User

Usage:

Syntax

Response

PWR-LVL?

PWR-LVL

LVL

Query the "full" and "standby" LED status. (Device reports to all protocol ports on any change)

LVL

= (0 = no LED, 1 = standby LED on, 2 = full LED on)

SCHED?

Cmd Short

Description

Command Type

Permission

Query saved scheduling

PL-50

User

Usage:

Syntax

Response

SCHED?

SCHED?

CHNL

,DAY

CHNL

,DAY

,SCHEDULINGS

= (1-5)

CHNL

= (1-7) OR (SUN,MON,TUE,WED,THU,FRI,SAT)

DAY

SCHEDULINGS

= (start-end) example: 8:29-8:32

SWITCH

Cmd Short

Description

Command Type

Permission

Channel switch

PL-50

User

Usage:

Syntax

Response

SWITCH

,

SWITCH

,

CHNL

STATUS

CHNL

STATUS

RESULT

CHNL = (1-5)

STATUS = (0=OFF,1=ON,2=ON-SCHEDULER,3=OFF-SCHEDULER ,4=ACTIVE-MEASURE,5=STANDBY-

MEASURE)

45

Image 49

Contents Model Contents Instruction Codes43 FiguresTables Getting Started IntroductionP3K Wizard Software Quick StartGetting Started Ethernet OverviewYour PL-50 Power Controller Monitor Your PL-50 Power Controller MonitorPL-50 Power Controller Monitor Front Panel Feature Function PL-50 Power Controller Monitor FeaturesBefore Installing in a Rack Installing in a RackConnecting the PL-50 Connecting the PL-50 Power Controller MonitorControlling the PL-50 via the Ethernet Port Connecting the RelaysRight-click Local Area Connection Properties Local Area Connection Properties window appearsConnecting via a Straight-Through Cable Upload Main Screen Click the Connect button Connect screen appears as followsIf required, make changes and click Save. If not, click Exit Following window appears Controlling via the Embedded Web PagesRunning the Application Panel Screen Scheduler Screen Scheduler Screen FeaturesHelp BOX Channel Settings Screen Features Define the Channel Settings screenDefine the Alerts screen Alerts Screen FeaturesSetting the Alarms Power Measurement Screen Features Define the Power Measurement screenPower ON/OFF Order Screen This page lets you set the power on and OFF order and delay Configurations Screen Security System Enabled Enable Security SystemSecurity System DIP-switch Settings Operating Your PL-50 Power Controller MonitorDIP-switch Definitions Calibrating via the Front Panel ButtonsOperating Your PL-50 Power Controller Monitor Upgrading the Firmware Flash Memory UpgradeUpload Screen Click the Connect button Connect Window appears see FigureConnection Time Out Message Machine is now connectedUpload Connected Upload Progress Restart Message When the update is finished, the restart message appearsIncludes the technical specifications Technical SpecificationsTechnical Specifications1 of the PL-50 Changing the Device ParametersProtocol 3000 Syntax Kramer ProtocolHost message format CR LFCommand Command TermsCommon Commands Name FactoryNAME? NAME? NameSecurity Commands Result and Error CodesThese commands are used by network devices running Protocol Network Setting CommandsNET-DHCP? NET-DHCPNET-GATE NET-GATE?Instruction Codes ALARM-ON ALARM-OFFALARM-ON Result ALARM-ON? ALARM-START-ASMES-MODE SwitchLVL SCHED?SWITCH-ORDER SWITCH?SWITCH-ORDER-DELAY SWITCH-ORDER-DELAY?Limited Warranty 2900-000576 REV