Compaq 3000 Series manual Initiating a Self-test

Page 44

Operation 3-11

Initiating a Self-test

To initiate a self-test, press the TEST/ALARM RESET button and hold for three seconds. The UPS acknowledges compliance with five beeps.

1

Figure13-4. The TEST/ALARM RESET button

TEST/ALARM RESET button

IMPORTANT: A portion of the self-test requires battery power; the self-test cannot be initiated if the batteries are less than 90% charged.

During the self-test, it is normal for the UPS to turn on individual LEDs momentarily; however, if an alarm condition is detected, the UPS will turn on the appropriate LED and may sound an audio alarm.

WARNING: To reduce the risk of electric shock from earth conductor leakage current, use the self-test procedure to check the UPS batteries (rather than unplugging the UPS).

For the meaning of individual LEDs, see “Front Panel LEDs in the Standby and Operate Modes,” in this chapter.

For information on what to do if the self-test detects a problem, see Chapter 6, “Troubleshooting.”

Image 44
Contents 3000SeriesUPS Page Contents Installation Iv Compaq 3000 Series UPS Operation and Reference GuideAppendix a Appendix C Vi Compaq 3000 Series UPS Operation and Reference GuideAbout This Guide Text ConventionsViii Compaq 3000 Series UPS Operation and Reference Guide Symbols in TextSymbols on Equipment Precautions About This GuideCompaq 3000 Series UPS Operation and Reference Guide Rack StabilityGetting Help Compaq Technical Support Compaq Website Compaq Authorized ResellerOverview Compaq 3000 Series UPS Models Front PanelsSeries UPS Models 2Compaq 3000 Series UPS Operation and Reference GuideRear Panels Overview4Compaq 3000 Series UPS Operation and Reference Guide Communications port Standard UPS Features 6Compaq 3000 Series UPS Operation and Reference GuidePower Management Software Communications Port8Compaq 3000 Series UPS Operation and Reference Guide Compaq Power Management SoftwareHardware Option Cards Compaq Multi-Server UPS Card Compaq Scalable UPS Card10Compaq 3000 Series UPS Operation and Reference Guide Remote Emergency Power Off Repo PortCompaq SNMP-EN Internal Adapter Warranties $25,000 Computer Load Protection GuaranteePre-Failure Battery Warranty Installation Items supplied with the UPS kit Installation RequirementsItems not supplied with the UPS kit Installation Before Starting the UPSRack Mounting the UPS Connecting to the Communications Port Connecting the Remote Emergency Power OffRemoving the connector block Checking the Battery Recharge Date Label Starting the UPSConnecting the UPS to Utility Power Connecting Devices to the UPSPowering up the UPS Front panel LED display and controlsCompleting the Installation Check the front panel LED displayPlacing the UPS in Operate mode Installation is Now CompleteOperation Standby Mode Operate ModeConfigure Mode Modes of OperationOperation Sleep ModeFront Panel Controls 4Compaq 3000 Series UPS Operation and Reference Guide AC Input LEDs Front Panel IndicatorsFront Panel LEDs Standby and Operate Modes Battery Service LED Site Wiring Fault LEDBattery Charge LEDs On LED Load Level LEDsCommunication LED Overcurrent Protection Overcurrent ProtectionPlacing the UPS in Operate Mode Returning to Standby Mode Standby mode controlsInitiating a Self-test Audio Alarm Silencing an Audio AlarmAudio Alarm Conditions 12Compaq 3000 Series UPS Operation and Reference GuideOperation Configuration Placing the UPS in Configure Mode Configure mode controls On LED LED On buttonConfiguration Parameters and their LED Indicators ConfigurationConfiguration Parameters/LED Indicators ExplanationConfiguration Parameters/LED Indicators Changing Configuration Parameters Optimizing Battery Life By Matching the Utility Voltage Nominal Configuration Operating Ranges VAC North America and Japanese Models Operating Ranges VAC All High Voltage ModelsBattery Maintenance 2Compaq 3000 Series Operation and Reference Guide Charging Batteries When to Replace BatteriesBattery Maintenance Pre-Failure Battery Warranty Obtaining New BatteriesReplacing Batteries 4Compaq 3000 Series Operation and Reference GuideRemoving the Battery Pack To replace batteries with the UPS Operate mode hot-swappingPreparing the UPS To replace batteries with the UPS Off6Compaq 3000 Series Operation and Reference Guide Removing the faceplateRemove two screws to access the battery pack Disconnecting the battery pack terminal connections 8Compaq 3000 Series Operation and Reference GuideInstalling New Batteries Sliding the battery pack out to reveal the second handleReplacing the battery cable retainer bracket Battery cables 10Compaq 3000 Series Operation and Reference GuideTesting New Batteries 12Compaq 3000 Series Operation and Reference Guide Care and Storage of BatteriesDisposing of Used Batteries Troubleshooting Troubleshooting During Start Troubleshooting Guide UPS StartTroubleshooting Troubleshooting After StartTroubleshooting Guide After Start Troubleshooting Guide After Start Repairing the UPS Regulatory Compliance Notices Federal Communications Commission NoticeClass a Equipment Class B EquipmentRegulatory Compliance Notices A-3 ModificationsCables Canadian Notice Avis Canadien European Union NoticeJapanese Notice Taiwanese Notice Regulatory Compliance Notices A-5Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Physical Specifications Input SpecificationsTable C-1 Physical Specifications 3000 Series UPS Models Table C-2 Input Specifications 3000 Series UPS ModelsSpecifications C-3 Output SpecificationsTable C-3 Output Specifications 3000 Series UPS Models Table C-4 Output Specifications 3000 Series UPS Models OutputBattery Specifications Table C-6 Battery Specifications 3000 Series UPS ModelsSpecifications C-5 Table C-5 Overcurrent Protection Per ModelBattery Runtime Environmental Specifications Specifications C-7Numbers and Symbols IndexCompaq 3000 Series UPS Operation and Reference Guide Index Http Index Important Safety Information Important Safety Information x, 2-2,2-3 Compaq 3000 Series UPS Operation and Reference Guide
Related manuals
Manual 24 pages 45.81 Kb