Alcatel Carrier Internetworking Solutions TQBJ0223 Installation, Projection schemes, Unit mm

Page 16

Installation

Projection schemes

Any of the following four projection schemes can be used depending on user’s needs or viewing conditions. Use “OPTION2” menu (chosen from the MAIN MENU) to choose the appropriate projection scheme. (page 33)

FLOOR	CEILING
FRONT
(Default position)
REAR

Installation geometry

When planning the projector and screen geometry, refer to the figure below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens tilt mechanism.

Side view
With optional ceiling mount		497
bracket (ET-PKD56H)		497
H		417-
H
L
SH	185	256
SH
H
Screen

Top view

unit : mm

SW		L	200
SW			200
			100
			100
	Screen		200
	Screen

L: Projection distance SH : Image height

SW : Image width

H : Distance from centre of lens to bottom edge of projected image.

Attention • Do not place or use one projector on top of another projection unit.

•Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be blocked. (page 59)

16

Image 16

Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Unit mmScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againFor RGB signals For DVI signalsFor S-Video/Video/YPBPRsignals On-screen menusMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Relay Lamp SelectRS-232C Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click Change passwordBasic control Detail control Monitor informationError information An error is detected by self- diagnosis Mail set upOn the next Authentication server set up Mail set up page ContinuingChange the authentication method as desired DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ELength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMInstallation dimensions diagram DimensionsUnit mm For business users in the European Union Trademark Acknowledgement