Alcatel Carrier Internetworking Solutions TQBJ0223 manual Error information

Page 40

Using Web Browser Control

Error information page

When is displayed on the status information screen, click it to display the error details.

OK: Normal operation

FAILED: Occurrence of trouble

Note • Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.

When [FAILED] has appeared for an item

Parameter

Description

 

 

MAIN CPU BUS

Trouble has occurred in the microcomputer circuitry. Consult your dealer.

FAN

Trouble has occurred in the fan or its drive circuit. Consult your dealer.

OPTICS MODULE

The temperature inside the projector is high.

It may be that the projector is being used where the ambient temperature is

TEMPERATURE

high such as near a heating appliance.

 

INPUT AIR TEMPERATURE

The input air temperature is too high.

It may be that the projector is being used where the ambient temperature is

 

high such as near a heating appliance.

AROUND LAMP

The temperature near the lamp has risen very high.

TEMPERATURE

Something may be blocking the exhaust vent.

LAMP REMAIN TIME

The lamp runtime has exceeded the prescribed cumulative time, and it is

now time to replace the lamp.

 

LAMP STATUS

The lamp has failed to light.

Wait a short while for the lamp to cool off, and then turn on the power.

 

SHUTTER

Trouble has occurred in the shutter circuitry. Consult your dealer.

AIR FILTER

Too much dust accumulates on the air filter.

Turn off the MAIN POWER switch using the procedure on page 22 and

 

clean the air filter (refer to page 51).

OPTICS MODULE TEMP.SENSOR

Trouble has occurred in the temperature detection sensor inside the

projector. Consult your dealer.

 

INPUT AIR TEMP.SENSOR

Trouble has occurred in the sensor used to detect the input air temperature.

Consult your dealer.

 

AROUND LAMP

Trouble has occurred in the temperature detection sensor around lamps.

TEMP. SENSOR

Consult your dealer.

BATTERY

The backup battery has been run out. Consult your dealer.

AIRFLOW SENSOR

Trouble has occurred in the air volume sensor. Consult your dealer.

COLOR WHEEL

Trouble has occurred in the colour wheel or the colour wheel drive circuit.

Consult your dealer.

 

COVER OPEN

The lamp unit cover is not properly fitted. Check the fitting of the lamp unit

cover. (page 53)

 

 

 

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Unit mmScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againFor RGB signals For DVI signalsFor S-Video/Video/YPBPRsignals On-screen menusMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Relay Lamp SelectRS-232C Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click Change passwordBasic control Detail control Monitor informationError information An error is detected by self- diagnosis Mail set upOn the next Authentication server set up Mail set up page ContinuingChange the authentication method as desired DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ELength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMInstallation dimensions diagram DimensionsUnit mm For business users in the European Union Trademark Acknowledgement
Top Page Image Contents