Alcatel Carrier Internetworking Solutions TQBJ0223 manual For business users in the European Union

Page 60

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new

product.

Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Note:

Purchase of this equipment includes the rights to use this software (the built-in microcomputer and information recorded on ROMs) but does not grant copyrights. Do not reverse engineer, change or modify the software. The guarantee will not be valid for any malfunctions caused by such actions.

Trademark Acknowledgement

•VGA and XGA are trademarks of International Business Machines Corporation.

•S-VGA is a registered trademark of the Video Electronics Standards Association.

•“Microsoft Windows” is a registered trademark of the Microsoft Corporation (U.S.A.) in the U.S. and other countries.

•“Netscape” and “Netscape Navigator” are registered trademarks of the Netscape Communications Corporation in the U.S. and other countries.

•Digital Light Processing, DLP, and DLP™ CHIP are registered trademarks of the Texas Instruments.

•PJLink™ is the applied-for trademark or a registered trademark in Japan, USA, and in other countries and regions.

•HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI

Licensing LLC.

All other trademarks are the property of the various trademark owners.

Matsushita Electric Industrial Co., Ltd

Web Site : http://panasonic.net

© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.

M0607-0

Page 59 Page 60
Image 60
Page 59 Page 60
Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Unit mmProjection distance by projection lens Screen aspect ratioScreen aspect ratio Calculation formulas for projection distance by lens types Setup precautions ConnectionPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againFor RGB signals For DVI signalsFor S-Video/Video/YPBPRsignals On-screen menusMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Select Lamp RelayRS-232C Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click Change passwordBasic control Detail control Monitor informationError information Mail set up An error is detected by self- diagnosisOn the next Mail set up page Continuing Authentication server set upChange the authentication method as desired DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ELength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramUnit mm For business users in the European Union Trademark Acknowledgement
Top Page Image Contents