Alcatel Carrier Internetworking Solutions TQBJ0223 manual Projection, Powering up the projector

Page 21

Projection

 

 

 

R/PR G/Y B/PB

SYNC/HD VD

 

VIDEO IN S-VIDEO IN

RGB 1 IN

 

 

REMOTE 1

REMOTE 2 IN

IN

SE

IN OUT

 

 

 

Powering up the projector

When using an optional lens, install a projection lens before powering up the projector. (Refer to page 23.)

Remove the lens cover beforehand.

Connect the supplied power cord. (220 - 240 V AC, 50 Hz/60 Hz)

Press the “ I ” marked side of the MAIN POWER switch to turn on the power.

The power indicator lights up red, and the projector is placed in the standby mode.

Press the “ I ” button. [on the main unit or the remote control]

The power indicator illuminates in green and soon the image is projected on the screen.

Making adjustment and selection

It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.

<Using the remote control>

Press the FOCUS button to roughly adjust the focus of the lens.*

Set the projection scheme in “INSTALLATION” setting. (page 33)

Select the input signal by pressing the input selector button to toggle through RGB1, RGB2, VIDEO, S-VIDEO and DVI-D.

Turn the feet, and adjust the tilt of the main unit in the front and rear or left and right.

ENGLISH

Note • If the projector is powered up at about 0 ˚C, a warm-up period of approximately five

minutes may be necessary to start projection.

The temperature monitor (TEMP) lights during the warm-up period.

When the warm-up is completed, the temperature monitor (TEMP) turns off and the image is projected on the screen.

If the surrounding temperature is very low and the warm-up period exceeds five minutes, the control determines it as an abnormal condition and turns off the power automatically. If this happens, raise the surrounding temperature to 0 °C or higher and then turn the main power “on” and turn the power “on” ( ).

Use the lens left/right adjustment dial to adjust the direction of the lens. (page 24)

Press the SHIFT button to adjust the “SHIFT”.*

Press the AUTO SETUP button if the input signal is RGB/DVI signal. (page 24)

Press the ZOOM button to fit the image size to the screen size.*

Press the FOCUS button again to adjust the “FOCUS”.*

Press the ZOOM button again to adjust the “ZOOM” and fit the image size to the screen size.*

*When operating at the projector, please refer to page 23.

21

Image 21
Contents Model No. PT-D4000E Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Do not use or handle the batteries improperly Remove empty batteries from the remote control at onceDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlInstallation geometry InstallationProjection schemes Unit mmProjection distance by projection lens Screen aspect ratioScreen aspect ratio Calculation formulas for projection distance by lens types Setup precautions ConnectionPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV productsMaking adjustment and selection Powering up the projectorPress the I button. on the main unit or the remote control When operating at the projector, please refer toDirect power off function Powering off the projectorHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Press the Status button on the remote control Automatic adjustmentStatus function Press the Shutter button againFor DVI signals For RGB signalsFor S-Video/Video/YPBPRsignals On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Zoom Clock PhaseKeystone Digital Cinema RealityXGA Mode Input ResolutionSxga Mode Clamp PositionOPTION1 settings DVI Edid DVI Signal LevelFUNC1 OSD PositionInstallation OPTION2 settingsProjector ID AltitudeLamp Select Lamp RelayRS-232C Password Auto Power OFFSystem Information Date and TimeConnecting the PC Setting the networkSystem requirements Connection exampleAccessing from the Web browser Using Web Browser ControlPassword change Click Change passwordBasic control Monitor information Detail controlError information Mail set up An error is detected by self- diagnosisOn the next Mail set up page Continuing Authentication server set upChange the authentication method as desired Ping test DNS server set upAdjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPassword Change Setting the securityDisplay Setting Control Device SetupPin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit When to replace the Lamp unitLamp AfterRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeInstallation procedure Ceiling Mount Bracket SafeguardsNot turn on Power doesNo image Image is blurredPT-D4000E SpecificationsOutside dimensions Length of power cord CabinetRemote control Power source Replacement lamp unitPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListDimensions Installation dimensions diagramUnit mm Trademark Acknowledgement For business users in the European Union