Alcatel Carrier Internetworking Solutions TQBJ0223 Basic menu operations, Menu items setting

Page 26

On-screen menus

Basic menu operations

Press the MENU button.

The MAIN MENU appears on the screen.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

OPTION1

OPTION2

TEST PATTERN

NETWORK

SECURITY

MENU SELECT

SUB MENU

Select (highlight) the desired item with

the or button.

Selected items are displayed in yellow.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

OPTION1

OPTION2

TEST PATTERN

NETWORK

SECURITY

MENU SELECT

SUB MENU

Press the ENTER button to enter your selection.

The submenu for the selected option will now open. (e.g. : POSITION Menu)

POSITION

SHIFT

ASPECT	4:3
ZOOM
CLOCK PHASE	+16
KEYSTONE

MENU SELECT

SUB MENU

Highlight the desired adjustment item

with the or buttons, then change the parameter value with the or buttons.

(Example of separate adjustment screen)

CLOCK PHASE

+16

•If no button is operated for approx. 5 seconds while a bar graph is displayed, the screen will return to the previous page.

Returning to the previous page

•Pressing the MENU button returns the screen to the previous menu page.

•When the MAIN MENU is on the screen, pressing the MENU button clears all menus from the screen.

Menu items shown in black characters

•Some menu items may not be valid for certain signal formats applied to the projector.

The menu items that cannot be adjusted or used are shown in black characters, and they cannot be selected.

Menu items setting

•The bottom prompt line differs on each menu

depending on the selected menu option:

• A prompt “ CHANGE” appears when changing the setting.

• A prompt “ ADJUST ” appears for a separate bar graph.

Resetting to the factory default

DEFAULT button is used to reset all of the projector adjustment values to the default levels which were set at the time of shipment from the factory.

PICTURE

	PICTURE MODE	STANDARD
	CONTRAST	0
	BRIGHTNESS	0
	COLOR	0
	TINT	0
	COLOR TEMP	DEFAULT
	WHITE GAIN	+6
	SYSTEM DAYLIGHT VIEW	OFF

SHARPNESS	+6
NOISE REDUCTION	1

AI	ON
SYSTEM SELECTOR	AUTO

MENU SELECT

ADJUST

26

Image 26

Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Unit mmScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Pin assignments on the RGB2 input terminal are as follows Setup precautionsConnection Example of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection When operating at the projector, please refer toPowering off the projector Direct power off functionHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againFor S-Video/Video/YPBPRsignals For RGB signalsFor DVI signals On-screen menusBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealitySxga Mode Input ResolutionXGA Mode Clamp PositionOPTION1 settings FUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeRS-232C Lamp SelectLamp Relay System Information Auto Power OFFPassword Date and TimeSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click Change passwordBasic control Detail control Monitor informationError information On the next Mail set upAn error is detected by self- diagnosis Change the authentication method as desired Mail set up page ContinuingAuthentication server set up DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D4000ERemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMUnit mm DimensionsInstallation dimensions diagram For business users in the European Union Trademark Acknowledgement