Alcatel Carrier Internetworking Solutions TQBJ0223 DVI Edid, FUNC1, OSD Position, OSD Memory

Page 32

OPTION1 settings

DVI EDID

When the projector and external equipment are connected by DVI connection but a proper image cannot be obtained, switch this setting.

EDID1

Select this mainly when external equipment (DVD player, etc.) that outputs movie video signals is connected to the DVI terminal.

EDID2:PC

Select this mainly when external equipment (personal computer, etc.) that outputs still image video signals is connected to the DVI terminal.

Mode

EDID data

 

480p, 576p, 1080/60i, 1080/50i,

EDID1

720/60p, 720/50p, 1080/60p,

 

1080/50p

 

VGA60, SVGA60, XGA50, XGA60,

FUNC1

The user can set the function for the remote control’s FUNC1 button.

SYSTEM SELECTOR:

The button functions in the same way as “SYSTEM SELECTOR” of “PICTURE”.

SYSTEM DAYLIGHT VIEW:

This button has the same functions as

“SYSTEM DAYLIGHT VIEW” of “PICTURE”.

SUB MEMORY LIST:

This button has the same functions as “SUB MEMORY LIST” of “OPTION1”.

OSD POSITION

The user can specify the position of the on-screen menu indications.

EDID2:PC

XGA70, XGA75, XGA85, SXGA60

Note • The optimum setting differs according to the connected external equipment. Be sure to check the operating instructions for the external equipment, etc.

1 (Top left of the screen)

9 (Bottom right of the screen)

8 (Right centre of the screen)

2 (Left centre of the screen)

3 (Bottom left of the screen)

4 (Top centre of the screen)

5 (Centre of the screen)

•Depending on the setting, some equipment may not provide images or otherwise operate properly.

DVI SIGNAL LEVEL

When the projector and external equipment are connected by DVI connection but a proper image cannot be obtained, switch this setting.

0-255:PC

Select this mainly when connecting external equipment (personal computer, etc.) using the DVI terminal output.

16-235

Select this mainly when connecting external equipment (DVD player, etc.) using the HDMI terminal output with a conversion cable, etc.

Note • The optimum setting differs according to the connected external equipment. Be sure to check the operating instructions for the external equipment, etc.

•Depending on the setting, some equipment may not provide images or otherwise operate properly.

7 (Top right of the screen)

6 (Bottom centre of the screen)

OSD MEMORY

This lets you save the cursor position in on-screen menus.

ON : The cursor position is saved.

OFF : The cursor position is not saved.

Note • Even when this is set to “ON”, the cursor position is not saved if the main power of the projector is turned off.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Unit mmScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Pin assignments on the RGB2 input terminal are as follows Setup precautionsConnection Example of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control When operating at the projector, please refer toPowering off the projector Direct power off functionHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againFor RGB signals For DVI signalsFor S-Video/Video/YPBPRsignals On-screen menusMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeRS-232C Lamp SelectLamp Relay Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click Change passwordBasic control Detail control Monitor informationError information On the next Mail set upAn error is detected by self- diagnosis Change the authentication method as desired Mail set up page ContinuingAuthentication server set up DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ELength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMUnit mm DimensionsInstallation dimensions diagram For business users in the European Union Trademark Acknowledgement
Top Page Image Contents