Alcatel Carrier Internetworking Solutions TQBJ0223 manual How to adjust the lens

Page 23

How to install and remove the projection lens

How to install the projection lens

Align the guide of the projection lens with the guide groove in the main unit. Turn the lens clockwise until it clicks into place.

Guide groove Guide

Guide groove

Guide

How to adjust the lens

How to adjust the FOCUS, ZOOM and SHIFT

The focus, zoom and up/down position of the images projected on the screen can be adjusted while the projector is positioned appropriately in relation to the screen.

At the projector

Press LENS on the control panel on the main unit.

Pressing the button changes the setup screen in the order of “FOCUS”, “ZOOM” and “SHIFT”.

Press to select an item and adjust it.

Using the remote control

Press LENS (FOCUS/ZOOM/SHIFT) on the remote control.

ENGLISH

Lens signal contact

Projection lens

When the FOCUS button is pressed :

The focus is adjusted.

Attention • Turn the lens counterclockwise and confirm that the lens does not come

off.

How to remove the projection lens

Turn the lens counterclockwise as far as it will go.

While holding down the lens release button, turn the lens further counterclockwise.

Remove the lens.

Lens release button

Note • Before replacing the lens, turn off the projector’s power.

•Do not touch the lens signal contact. Dust or dirt may cause defective contact.

•Do not touch the surface of the projection lens with your bare hands.

•Store the replaced lens where it will be free from vibration and impact.

When the ZOOM button is pressed :

The zoom is adjusted.

When the SHIFT button is pressed :

The shift is adjusted.

Press to select an item and adjust it.

Caution

Be careful not to catch your fingers between the lens and shroud when shifting the lens.

Note

• When a lens without zoom functions

 

is used, the lens zoom adjustment

 

menu will still displayed, but no

 

operations can be performed using

 

the items on this menu.

 

• By shifting the lens up/down position,

 

it is possible to make adjustments

 

upward or downward from the

 

standard position in the direction of

 

the upper 50 % of the projected

 

screen height. However, when using

 

ET-DLE050 lens, the shift adjustment

 

is not possible.

 

• Operations can be performed faster

 

by holding down the

 

buttons for about 3 or more seconds.

 

• Do not adjust the lens focus in the

 

initial period (within 30 minutes) after

 

switching on.

 

• A warm-up period of at least 30 minutes

 

is recommended before using the

 

projector.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model No. PT-D4000E Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitElectric shocks can result if this is not done AccessoriesDo not use the old lamp unit Do not place the projector in extremely hot locationsPrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Connect to the projector to use with a cable Setting projector ID number to remote controlUnit mm InstallationInstallation geometry Projection schemesScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Pin assignments on the RGB2 input terminal are as follows Setup precautionsConnection Example of connecting with PCs Example of connecting with AV productsWhen operating at the projector, please refer to Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionOn-screen menus For RGB signalsFor DVI signals For S-Video/Video/YPBPRsignalsReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionXGA Mode Sxga ModeOPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDRS-232C Lamp SelectLamp Relay Date and Time Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick Change password Using Web Browser ControlAccessing from the Web browser Password changeBasic control Monitor information Detail controlError information On the next Mail set upAn error is detected by self- diagnosis Change the authentication method as desired Mail set up page ContinuingAuthentication server set up Ping test DNS server set upAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D4000E SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListUnit mm DimensionsInstallation dimensions diagram Trademark Acknowledgement For business users in the European Union
Top Page Image Contents