Alcatel Carrier Internetworking Solutions TQBJ0223 manual Setting the security, Text Change

Page 47

Setting the security

The projector’s security function enables the password input screen to be displayed or a company’s URL address to be set and displayed underneath the projected images.

PASSWORD

INPUT

SET

(When using the projector for the first time)

Press the , , , , , , and buttons in this order, and press the ENTER button.

(When the password has been changed)

Input the new password, and press the ENTER button.

TEXT CHANGE

The text which is to be displayed when “TEXT” has been selected for the “DISPLAY SETTING” can be changed. Press the ENTER button.

Select the text using the , , , buttons, and press the ENTER button. (Up to 22 alphanumerics can be input in succession.)

Select “OK” using the , , , buttons, and press the ENTER button.

To cancel the change at any time, select

CANCEL.

PASSWORD

It is possible to display the password input screen each time the power is turned on. If this option is used, no operations except for the POWER button can be performed without inputting the correct password.

ON : Password input is enabled.

OFF : Password input is disabled.

PASSWORD CHANGE

The password can be changed. Press the ENTER button.

Set the password using the , , ,

buttons (up to 8 buttons can be set).

Press the ENTER button.

Confirm the password by inputting it again.

Press the ENTER button. (This completes the settings.)

Note • Asterisks ( ) will appear on the screen in the place of the actual password when the password is input.

If the password is input incorrectly, the display returns to “NEW”. Input the correct password.

DISPLAY SETTING

The image can be displayed based on the settings

below.

 

OFF

: The normal image is displayed.

TEXT

: Preset text is constantly displayed

 

under the projected image.

LOGO1 : The picture registered by the user will be projected.

LOGO2 : The Panasonic logo is projected.

CONTROL DEVICE SETUP

It is possible to restrict operation from the remote control and the main unit controls.

CONTROL PANEL :

Operation from the main unit controls can be restricted.

ENABLE : Main unit control operation is enabled

DISABLE : Main unit control operation is disabled

REMOTE CONTROLLER :

Operation from the remote control can be restricted.

ENABLE : Remote control operation is enabled

DISABLE : Remote control operation is disabled

Note • Setting changes will be reflected only

when you select “OK” at the confirmation screen displayed after you press the ENTER button at the “ENABLE/DISABLE” menu. When the setting has been reflected, the on- screen menu disappears.

To continue and perform other operations, press the MENU button and display the MAIN MENU.

When you attempt to operate controls (remote control or main unit) that are set to “DISABLE”, the password input screen is displayed. To change the setting, input the security password and change the operation setting. The password input screen disappears when you press the MENU button or if you do not perform any operation for 10 seconds.

ENGLISH

47

Image 47
Contents Model No. PT-D4000E Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitElectric shocks can result if this is not done AccessoriesDo not use the old lamp unit Do not place the projector in extremely hot locationsPrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Connect to the projector to use with a cable Setting projector ID number to remote controlUnit mm InstallationInstallation geometry Projection schemesScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Pin assignments on the RGB2 input terminal are as follows Setup precautionsConnection Example of connecting with PCs Example of connecting with AV productsWhen operating at the projector, please refer to Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionOn-screen menus For RGB signalsFor DVI signals For S-Video/Video/YPBPRsignalsReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionXGA Mode Sxga ModeOPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDRS-232C Lamp SelectLamp Relay Date and Time Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick Change password Using Web Browser ControlAccessing from the Web browser Password changeBasic control Monitor information Detail controlError information On the next Mail set upAn error is detected by self- diagnosis Change the authentication method as desired Mail set up page ContinuingAuthentication server set up Ping test DNS server set upAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D4000E SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListUnit mm DimensionsInstallation dimensions diagram Trademark Acknowledgement For business users in the European Union