Alcatel Carrier Internetworking Solutions TQBJ0223 manual OPTION1 settings

Page 31

OPTION1 settings

 

OPTION1

 

 

 

 

 

 

 

COLOR CORRECTION

USER

 

 

CONTRAST MODE

NORMAL

 

 

AUTO SIGNAL

OFF

 

 

BACK COLOR

BLUE

 

 

STARTUP LOGO

OFF

 

 

SUB MEMORY LIST

 

 

 

DVI EDID

EDID2:PC

 

 

DVI SIGNAL LEVEL

0-255:PC

 

 

FUNC1

 

 

 

OSD POSITION

1

 

 

OSD MEMORY

ON

 

MENU SELECT

CHANGE

COLOR CORRECTION

OFF : This is the standard setting.

USER : The six colours of red, green, blue, cyan, magenta and yellow can be adjusted and registered for each of four signal systems: Video, S-Video, RGB and

YPBPR.

Press the ENTER button to make the detailed settings.

COLOR CORRECTION

 

 

RGB

R

0

G

0

B

0

Cy

0

Mg

0

Ye

0

MENU SELECT

 

ADJUST

 

The current signal system is displayed.

CONTRAST MODE

There are two modes for adjusting to the operating environment.

NORMAL : The brightness is set to maximum.

HIGH : The contrast is set to maximum.

AUTO SIGNAL

The position where the screen is displayed can be adjusted automatically without pressing the AUTO SETUP button on the remote control each time signals are input when signals are input frequently such as when the projector is used at a conference.

ON

: Auto setup is performed automatically

 

when the video signals of the images

 

being projected have changed.

OFF

: The input auto setup function is set to

 

OFF.

BACK COLOR

You can set the colours of the screen when no signal is input to the projector.

BLUE

: Set screen colour to blue.

BLACK

: Set screen colour to black.

LOGO1 : The picture registered by the user will be projected.

LOGO2 : The Panasonic logo is projected.

STARTUP LOGO

This sets the startup logo that is projected when the power is turned on.

LOGO2 : This is the standard setting.

The Panasonic logo is projected. NONE : “STARTUP LOGO” is disabled. LOGO1 : The picture registered by the user will

be projected.

Note • Separate software is required in order to create the pictures to use for “LOGO1”. Consult your dealer.

SUB MEMORY LIST

Multiple sets of image adjustment data (PICTURE, POSITION, ADVANCED MENU adjustment values) for the same kind of signal can be registered.

SUB MEMORY LIST

- : RGB1-XGA60

1:RGB1-XGA60

2:VIDEO-NTSC

SELECT STORE

RETURN

Registering in sub memory

Select the sub memory number to be registered

using the buttons. Press the ENTER button.

Note • Sub memories range from 1 to 8.

How to select sub memory

Select sub memory number (1 to 8) using the buttons. Select “–” if you do not wish to

use the sub memory.

Press the ENTER button.

Note • You cannot select sub memory of a different signal system.

How to erase sub memory

Select sub memory number (1 to 8) corresponding

to sub memory to be erased using buttons. Press the DEFAULT button.

Read the confirmation message and select.

ENGLISH

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model No. PT-D4000E Commercial UseDear Panasonic Customer Important Safety NoticeImportant the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitElectric shocks can result if this is not done AccessoriesDo not use the old lamp unit Do not place the projector in extremely hot locationsPrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlUnit mm InstallationInstallation geometry Projection schemesScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV productsWhen operating at the projector, please refer to Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionOn-screen menus For RGB signalsFor DVI signals For S-Video/Video/YPBPRsignalsReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionXGA Mode Sxga ModeOPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDLamp Relay Lamp SelectRS-232C Date and Time Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick Change password Using Web Browser ControlAccessing from the Web browser Password changeBasic control Monitor information Detail controlError information An error is detected by self- diagnosis Mail set upOn the next Authentication server set up Mail set up page ContinuingChange the authentication method as desired Ping test DNS server set upAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D4000E SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsUnit mm Trademark Acknowledgement For business users in the European Union
Top Page Image Contents