Alcatel Carrier Internetworking Solutions TQBJ0223 manual Lamp Select, Lamp Relay, RS-232C

Page 34

OPTION2 settings

LAMP SELECT

“LAMP SELECT” is used to choose from “SINGLE” and “DUAL” modes depending on user’s needs or viewing conditions.

In “SINGLE” mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified.

DUAL : Two lamps are used simultaneously.

SINGLE : One of either lamps is used (lamp with shorter operating hours is automatically selected).

LAMP1 : Lamp Unit 1 is always used.

LAMP2 : Lamp Unit 2 is always used.

When one of the above settings is selected, it will take effect after the ENTER button is pressed.

Note • If, in the “SINGLE”, “LAMP1” or “LAMP2” mode, one lamp remains off

or the currently active lamp exceeds 3 000 hours of cumulative operating time, the other lamp will light. If, in the “DUAL” mode, one lamp remains off or the currently active lamp exceeds

3 000 hours of cumulative operating time, the other lamp alone will light. However, if both lamps remain off or the 3 000 hours of cumulative operating time are exceeded, the projector will enter the standby mode.

•The colours of the items indicate the status.

Green Current setting

Yellow Current setting (when a lamp fails or fails to light)

Red

Lamp that has failed to

 

light

White

Any other status

•If the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently.

LAMP RELAY

If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use.

OFF : This is the standard setting. “LAMP RELAY” is disabled.

00:00 - 23:00

:This can be set in one hour intervals from 00:00 to 23:00.

Note • Only when “DUAL” or “SINGLE” is selected in “LAMP SELECT”, “LAMP

RELAY” is active. If “LAMP1” or

“LAMP2” is selected, “LAMP RELAY” function is not available.

•When “DUAL” is selected in “LAMP SELECT”, only one lamp will light for a 4-hour period after the set time.

•When “SINGLE” is selected in “LAMP SELECT”, the lamp that was off at the set time will light, and then the lamp that was lighted until the set time will turn off.

•The setting time will be the local time. (page 35)

RS-232C

This sets the communication parameters at the serial terminals.

For details on the serial terminals, refer to “Using the serial terminals” (page 48).

(IN) BAUDRATE

: 9600, 19200 or 38400 is

 

selected.

(IN) PARITY

: NONE, EVEN or ODD is

 

selected.

(OUT) BAUDRATE: 9600, 19200 or 38400 is

 

selected.

(OUT) PARITY

: NONE, EVEN or ODD is

 

selected.

VPS SYSTEM

: MASTER or SLAVE is

 

selected.

GROUP

: A to Z is selected. MASTER

 

or SLAVE is also selected.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Commercial Use Model No. PT-D4000EImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Unit mmScreen aspect ratio Projection distance by projection lensScreen aspect ratio Calculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againFor S-Video/Video/YPBPRsignals For RGB signalsFor DVI signals On-screen menusBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealitySxga Mode Input ResolutionXGA Mode Clamp PositionOPTION1 settings FUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp SelectRS-232C System Information Auto Power OFFPassword Date and TimeSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click Change passwordBasic control Detail control Monitor informationError information An error is detected by self- diagnosis Mail set upOn the next Authentication server set up Mail set up page ContinuingChange the authentication method as desired DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D4000ERemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMInstallation dimensions diagram DimensionsUnit mm For business users in the European Union Trademark Acknowledgement
Top Page Image Contents