BenQ MP670 user manual Connecting S-Video source devices, Video device Audio device

Page 23

Connecting S-Video source devices

Examine your Video source device to determine if it has an unused S-Video output socket available:

If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector.

To connect the projector to an Audio source device:

1.Take a suitable audio cable and connect one end to the AUDIO OUT jack of the AV

device. Connect the other end of the cable to the AUDIO IN jack on the projector. Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 52 for details.

The final connection path should be like that shown in the following diagram:

AV device

English

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S-Video device

Audio device

 

 

 

 

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 20 for details.

Connection 23

Image 23
Contents MP626/MP670 Digital Projector WelcomeTable of contents Lens during operation. The intense Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Up/ Down Remote control effective rangeTimer On/Set up SourceReplace the tray Replacing the remote control batteryChoosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish Average MP626/670 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionWith a VGA to DVI-A cable Connecting a monitorTo connect the projector to a monitor With a VGA cableBetter video quality Connecting Video source devicesConnecting Audio Best video qualityHdmi cable Connecting Hdmi source devicesTo connect the projector to an Hdmi source device AV deviceAudio cable Connecting Component Video source devicesTo connect the projector to a Component Video source device To connect the projector to an Audio source deviceVideo device Audio device Connecting S-Video source devicesTo connect the projector to an S-Video source device To connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup Basic menuSetting a password Utilizing the password functionChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Keystone function Fine-tuning the image size and clarityUsing Auto Keystone Correcting keystoneMagnifying and searching for details Selecting the aspect ratio Playing 3D functionReal About the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode Picture modes for different types of signalsAdjusting Contrast Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessPress MODE/ENTER and the 3D Color Management page displays 3D Color ManagementPresentation Timer menu and press Mode Setting the presentation timerTo cancel the timer, perform the following steps Go to the System Setup BasicHiding the image Remote paging operationsFreezing the image Utilizing FAQ functionSetup Basic Panel Key Lock menu, and select Locking control keysOperating in a high altitude environment To activate the High Altitude ModeUntil the System Setup Advanced menu To highlight High Altitude ModeMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Shutting down the projector Personalizing the projector menu displayMenu system Color T1/T2/T3/T4 Temperature Primary color3D Color Hue Management Saturation Gain Save Settings Menu operationRight/Bottom-left FAQ-Image and Installation FAQ-Features and Service SourceProjector Position Front Table/Rear Table Rear Ceiling/Front CeilingReset All Settings Quick Cooling Off/On High Altitude Mode Audio SettingsLamp Mode Lamp SettingsAuto DisableDescription of each menu OffDynamic Color SpaceTimer counting direction Count Down Timer period 15 minTimer display Always Timer position Top-LeftReset lamp timer VolumePower On/Off ring tone On Lamp Mode NormalColor System ResolutionPicture Mode SourceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnglish Setup Advanced Lamp Settings Resetting the lamp timerOff Green IndicatorsRed Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartResolution Horizontal Vertical Pixel Mode Supported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputSXGA85 Supported timing for Hdmi Hdcp input1600 x 75.000 60.000 162.000 Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statementEnglish