BenQ MP670 user manual Press Exit to go back to the remote network operation

Page 47

i.These buttons function the same as the ones on the OSD menus or remote control. See "Using the menus" on page 26 and "Remote control" on page 11 for details.

The Menu button can also be used to go back to previous OSD menu, exit and save menu settings.

ii. To switch input source, click on your desired signal.

The tools page allows you to manage the projector, configure the Lan control settings and secure access of remote network operation on this projector.

iiii

iiiv

i.You can name the projector, keep track of its location and the person in charge of it.

ii.You can adjust the Lan Control Settings.

iii.Once set, access to the remote network operation on this projector has been password-protected.

iv.Once set, access to the tools page has been password-protected.

After making the adjustments, press the Send button and the data will be saved in the projector.

v. Press Exit to go back to the remote network operation page.

English

Operation 47

Image 47

Contents MP626/MP670 Digital Projector WelcomeTable of contents Lens during operation. The intense Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Up/ Down Remote control effective rangeTimer On/Set up SourceReplace the tray Replacing the remote control batteryChoosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish Average MP626/670 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionWith a VGA to DVI-A cable Connecting a monitorTo connect the projector to a monitor With a VGA cableBetter video quality Connecting Video source devicesConnecting Audio Best video qualityHdmi cable Connecting Hdmi source devicesTo connect the projector to an Hdmi source device AV deviceAudio cable Connecting Component Video source devicesTo connect the projector to a Component Video source device To connect the projector to an Audio source deviceVideo device Audio device Connecting S-Video source devicesTo connect the projector to an S-Video source device To connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup Basic menuSetting a password Utilizing the password functionChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Keystone function Fine-tuning the image size and clarityUsing Auto Keystone Correcting keystoneMagnifying and searching for details Selecting the aspect ratio Playing 3D functionReal About the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode Picture modes for different types of signalsAdjusting Contrast Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessPress MODE/ENTER and the 3D Color Management page displays 3D Color ManagementPresentation Timer menu and press Mode Setting the presentation timerTo cancel the timer, perform the following steps Go to the System Setup BasicHiding the image Remote paging operationsFreezing the image Utilizing FAQ functionSetup Basic Panel Key Lock menu, and select Locking control keysOperating in a high altitude environment To activate the High Altitude ModeUntil the System Setup Advanced menu To highlight High Altitude ModeMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Shutting down the projector Personalizing the projector menu displayMenu system Color T1/T2/T3/T4 Temperature Primary color3D Color Hue Management Saturation Gain Save Settings Menu operationRight/Bottom-left FAQ-Image and Installation FAQ-Features and Service SourceProjector Position Front Table/Rear Table Rear Ceiling/Front CeilingReset All Settings Quick Cooling Off/On High Altitude Mode Audio SettingsLamp Mode Lamp SettingsAuto DisableDescription of each menu OffDynamic Color SpaceTimer counting direction Count Down Timer period 15 minTimer display Always Timer position Top-LeftReset lamp timer VolumePower On/Off ring tone On Lamp Mode NormalColor System ResolutionPicture Mode SourceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnglish Setup Advanced Lamp Settings Resetting the lamp timerOff Green IndicatorsRed Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartResolution Horizontal Vertical Pixel Mode Supported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputSXGA85 Supported timing for Hdmi Hdcp input1600 x 75.000 60.000 162.000 Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statementEnglish