BenQ MP670 user manual Playing 3D function, Selecting the aspect ratio

Page 34

English

Playing 3D function

1.To enter the special preset mode, press MENU/EXIT and then press / until the

DISPLAY menu is highlighted, and press / to enable or disable 3D Sync. When the 3D Sync is enabled, the current picture mode adjustment will be disabled.

2.To invert the image, press MENU/EXIT and then press / until the DISPLAY menu is highlighted, and press / to enable or disable 3D Sync Invert.

3.3D Requirement:

PC: PC with graphic card with stereo capability ( Quad buffer feature) and can run at 120Hz refresh rate.

Video: standard NTSC DVD player to output 60Hz movie.

55% of the brightness loss.

To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD devices under the 3D Disc Menu.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. For MP626 and MP670, the default aspect ratio is 4:3. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected image ratio (no matter what aspect the source is):

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Aspect Ratio.

3.Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

34 Operation

Image 34
Contents Welcome MP626/MP670 Digital ProjectorTable of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Source Remote control effective rangeTimer On/Set up Up/ DownReplacing the remote control battery Replace the trayPositioning your projector Choosing a locationObtaining a preferred projected image size Aspect display area Display areaEnglish MP626/670 projection dimensions AverageConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerWith a VGA cable Connecting a monitorTo connect the projector to a monitor With a VGA to DVI-A cableBest video quality Connecting Video source devicesConnecting Audio Better video qualityAV device Connecting Hdmi source devicesTo connect the projector to an Hdmi source device Hdmi cableTo connect the projector to an Audio source device Connecting Component Video source devicesTo connect the projector to a Component Video source device Audio cableTo connect the projector to an S-Video source device Connecting S-Video source devicesVideo device Audio device Connecting Composite Video source devices To connect the projector to a composite Video source deviceOperation Starting up the projectorUse / to highlight the System Setup Basic menu Using the menusUsing a security cable lock Securing the projectorUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUsing Auto Keystone Keystone functionMagnifying and searching for details Playing 3D function Selecting the aspect ratioAbout the aspect ratio RealPicture modes for different types of signals Using Wall ColorSelecting a picture mode Optimizing the imageAdjusting Brightness Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting ContrastAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant Color3D Color Management Press MODE/ENTER and the 3D Color Management page displaysGo to the System Setup Basic Setting the presentation timerTo cancel the timer, perform the following steps Presentation Timer menu and press ModeRemote paging operations Hiding the imageLocking control keys Utilizing FAQ functionSetup Basic Panel Key Lock menu, and select Freezing the imageTo highlight High Altitude Mode To activate the High Altitude ModeUntil the System Setup Advanced menu Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Personalizing the projector menu display Shutting down the projectorMenu operation Color T1/T2/T3/T4 Temperature Primary color3D Color Hue Management Saturation Gain Save Settings Menu systemRear Ceiling/Front Ceiling FAQ-Image and Installation FAQ-Features and Service SourceProjector Position Front Table/Rear Table Right/Bottom-leftLamp Settings Quick Cooling Off/On High Altitude Mode Audio SettingsLamp Mode Reset All SettingsOff DisableDescription of each menu AutoColor Space DynamicTimer position Top-Left Timer period 15 minTimer display Always Timer counting direction Count DownLamp Mode Normal VolumePower On/Off ring tone On Reset lamp timerSource ResolutionPicture Mode Color SystemMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageDo not turn the power on with the lamp cover removed Replacing the lampEnglish Resetting the lamp timer Setup Advanced Lamp SettingsRed IndicatorsOff Green Troubleshooting Specifications Projector specificationsDimensions Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputsSupported timing for Hdmi Hdcp input SXGA851600 x 75.000 60.000 162.000 Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directiveEnglish