BenQ MP670 Mute Off, Volume, Power On/Off ring tone On, Lamp Mode Normal, Reset lamp timer

Page 56

English

Advanced	5. SYSTEM
menu	SETUP:

		Selecting On enables the function and the projector cooling time will
	Quick	be shortened to a few seconds.
	Cooling	If you attempt to restart the projector right after the quick
	(On)	cooling process, it may not be turned on successfully and will
		rerun its cooling fans.
	High Altitude	A mode for operation in high altitude areas. See "Operating in a high
	Mode	altitude environment" on page 43 for details.
	(Off)
		Mute (Off)
	Audio Setting	Volume (5)
		Power On/Off ring tone (On)
		See "Adjusting the sound" on page 44 for details.
		Lamp Mode (Normal)
		See "Setting Lamp mode as Economic" on page 59 for details.
	Lamp	Reset lamp timer
	Lamp	See "Resetting the lamp timer" on page 63 for details.
	Settings	See "Resetting the lamp timer" on page 63 for details.
	Settings	Equivalent Lamp Hour
		Equivalent Lamp Hour
		See "Getting to know the lamp hour" on page 59 for details on
		how the total lamp hour is calculated.
		Change password
	Security	You will be asked to enter the current password before changing to a
	Settings	new one. See "Utilizing the password function" on page 27 for details.
		Power on Lock (Off)
	Baud Rate	Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	(115200)	download the projector’s firmware. This function is intended for
		qualified service personnel.
	Test Pattern	Selecting On enables the function and the projector displays the grid
	Test Pattern	test pattern. It helps you adjust the image size and focus and check
	(Off)	that the projected image is free from distortion.
		that the projected image is free from distortion.
	Closed	Selecting On enables the function. The closed captioning text is
	Caption	displayed if available.
	(CC1)	Close Caption will disable when aspect change to 16:9 or rear.
		Selecting On enables the function. The projector can output a VGA
	Standby	signal when it is in standby mode and the COMPUTER 1 and
	Standby	MONITOR OUT sockets are correctly connected to devices. See
	Monitor Out	"Connecting a monitor" on page 19 for how to make the connection.
	(Off)	Enabling this function slightly increases the standby power
		Enabling this function slightly increases the standby power
		consumption.
	Lan Control	Sets the networking and remote management of the projector. See
	Lan Control	"Controlling the projector through a Lan environment" on page 45 for
	Settings
	Settings	details.
		details.
	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Position, Phase, H. Size,
	Settings
	Settings	User 1, User 2, Language, Projector Position, High Altitude
		Mode, Security Settings, Baud Rate, Lan Control Settings.

56 Operation

Image 56

Contents Welcome MP626/MP670 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions ProjectorRemote control Remote control effective range Timer On/Set upSource Up/ DownReplacing the remote control battery Replace the trayPositioning your projector Choosing a locationObtaining a preferred projected image size Aspect display area Display areaEnglish MP626/670 projection dimensions AverageConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorWith a VGA cable With a VGA to DVI-A cableConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting Hdmi source devices To connect the projector to an Hdmi source deviceAV device Hdmi cableConnecting Component Video source devices To connect the projector to a Component Video source deviceTo connect the projector to an Audio source device Audio cableVideo device Audio device Connecting S-Video source devicesTo connect the projector to an S-Video source device Connecting Composite Video source devices To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signal Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Using Auto KeystoneCorrecting keystone Keystone functionMagnifying and searching for details Playing 3D function Selecting the aspect ratioAbout the aspect ratio RealUsing Wall Color Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant Color3D Color Management Press MODE/ENTER and the 3D Color Management page displaysSetting the presentation timer To cancel the timer, perform the following stepsGo to the System Setup Basic Presentation Timer menu and press ModeRemote paging operations Hiding the imageUtilizing FAQ function Setup Basic Panel Key Lock menu, and selectLocking control keys Freezing the imageTo activate the High Altitude Mode Until the System Setup Advanced menuTo highlight High Altitude Mode Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Muting the soundIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Personalizing the projector menu display Shutting down the projectorColor T1/T2/T3/T4 Temperature Primary color 3D Color Hue Management Saturation Gain Save SettingsMenu operation Menu systemFAQ-Image and Installation FAQ-Features and Service Source Projector Position Front Table/Rear TableRear Ceiling/Front Ceiling Right/Bottom-leftQuick Cooling Off/On High Altitude Mode Audio Settings Lamp ModeLamp Settings Reset All SettingsDisable Description of each menuOff AutoColor Space DynamicTimer period 15 min Timer display AlwaysTimer position Top-Left Timer counting direction Count DownVolume Power On/Off ring tone OnLamp Mode Normal Reset lamp timerResolution Picture ModeSource Color SystemMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageDo not turn the power on with the lamp cover removed Replacing the lampEnglish Resetting the lamp timer Setup Advanced Lamp SettingsOff Green IndicatorsRed Troubleshooting Specifications Projector specificationsDimensions Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputsSupported timing for Hdmi Hdcp input SXGA851600 x 75.000 60.000 162.000 Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directiveEnglish