BenQ MP670 Quick Cooling Off/On High Altitude Mode Audio Settings, Lamp Mode, Lamp Settings

Page 52

English

	Quick Cooling		Off/On

	High Altitude Mode		Off/On

	Audio Settings	Mute	Off/On
		Volume	Range : 0 ~ 10
		Power on/off	Off/On
		ring tone

		Lamp Mode	Normal/Economic
	Lamp Settings
	Lamp Settings	Reset lamp timer

		Equivalent Lamp Hour

	Security	Change password
	Settings	Power on Lock	Off/On

	Baud Rate		9600/19200/38400/57600/
5.	Baud Rate		115200
			115200

	Test Pattern		Off/On
SYSTEM	Test Pattern		Off/On
SYSTEM
SETUP:		Closed Caption	Off/On
SETUP:		Enable	Off/On
Advanced Closed Caption		Enable
		Caption Version	CC1/CC2/CC3/CC4

	Stabdby Monitor		Off/On
	Out		Off/On
	Out

		Control by	RS232/RJ45

			Network Status

			DHCP

	Lan Control		Projection IP Address
	Settings	Network Status	Subnet Mask

Default Gateway

DNS

Apply

Reset All Settings

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

The default values listed in this manual, especially on page 50-57, are for reference only. They may vary from the projectors due to the continuous improvement to the products.

52 Operation

Image 52

Contents Welcome MP626/MP670 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Remote control effective range Timer On/Set upSource Up/ DownReplacing the remote control battery Replace the trayPositioning your projector Choosing a locationObtaining a preferred projected image size Aspect display area Display areaEnglish MP626/670 projection dimensions AverageConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorWith a VGA cable With a VGA to DVI-A cableConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting Hdmi source devices To connect the projector to an Hdmi source deviceAV device Hdmi cableConnecting Component Video source devices To connect the projector to a Component Video source deviceTo connect the projector to an Audio source device Audio cableTo connect the projector to an S-Video source device Connecting S-Video source devicesVideo device Audio device Connecting Composite Video source devices To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Using Auto KeystoneCorrecting keystone Keystone functionMagnifying and searching for details Playing 3D function Selecting the aspect ratioAbout the aspect ratio RealUsing Wall Color Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant Color3D Color Management Press MODE/ENTER and the 3D Color Management page displaysSetting the presentation timer To cancel the timer, perform the following stepsGo to the System Setup Basic Presentation Timer menu and press ModeRemote paging operations Hiding the imageUtilizing FAQ function Setup Basic Panel Key Lock menu, and selectLocking control keys Freezing the imageTo activate the High Altitude Mode Until the System Setup Advanced menuTo highlight High Altitude Mode Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Personalizing the projector menu display Shutting down the projectorColor T1/T2/T3/T4 Temperature Primary color 3D Color Hue Management Saturation Gain Save SettingsMenu operation Menu systemFAQ-Image and Installation FAQ-Features and Service Source Projector Position Front Table/Rear TableRear Ceiling/Front Ceiling Right/Bottom-leftQuick Cooling Off/On High Altitude Mode Audio Settings Lamp ModeLamp Settings Reset All SettingsDisable Description of each menuOff AutoColor Space DynamicTimer period 15 min Timer display AlwaysTimer position Top-Left Timer counting direction Count DownVolume Power On/Off ring tone OnLamp Mode Normal Reset lamp timerResolution Picture ModeSource Color SystemMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageDo not turn the power on with the lamp cover removed Replacing the lampEnglish Resetting the lamp timer Setup Advanced Lamp SettingsRed IndicatorsOff Green Troubleshooting Specifications Projector specificationsDimensions Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputsSupported timing for Hdmi Hdcp input SXGA851600 x 75.000 60.000 162.000 Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directiveEnglish