BenQ MP670 user manual Operation, Starting up the projector

Page 25

Operation

Starting up the projector

1.Plug the power cord into the projector and

into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

2.Press POWER on the projector or

remote control to start the projector and a start up tone sounds. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see "Turning off the Power on/off ring tone" on page 44 for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

3. To use the OSD menus, please set them to your familiar

English

language first. See "Personalizing the projector menu display" on page 49 for details.

Please select language

4. If you are prompted for a password, press the arrow keys to enter a five digit password. See "Utilizing the password function" on page 27 for details.

5. Switch all of the connected equipment on.

6. The projector will start to search for input signals. The current input signal being scanned displays in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue displaying until an input signal is found.

Press Enter to confirm, Exit to leave

You can also press SOURCE on the projector or remote

control to select your desired input signal. See "Switching input signal" on page 30 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting.

See "Timing chart" on page 68 for details.

To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning if off.

Operation 25

Image 25
Contents MP626/MP670 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsRemote control Timer On/Set up Remote control effective rangeSource Up/ DownReplace the tray Replacing the remote control batteryChoosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish Average MP626/670 projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cableConnecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesAV device Hdmi cableTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an Audio source device Audio cableTo connect the projector to an S-Video source device Connecting S-Video source devicesVideo device Audio device To connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationUsing a security cable lock Using the menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Using Auto Keystone Fine-tuning the image size and clarityCorrecting keystone Keystone functionMagnifying and searching for details Selecting the aspect ratio Playing 3D functionReal About the aspect ratioSelecting a picture mode Using Wall ColorPicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Fine-tuning the image quality in user modesAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerGo to the System Setup Basic Presentation Timer menu and press ModeHiding the image Remote paging operationsSetup Basic Panel Key Lock menu, and select Utilizing FAQ functionLocking control keys Freezing the imageUntil the System Setup Advanced menu To activate the High Altitude ModeTo highlight High Altitude Mode Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Shutting down the projector Personalizing the projector menu display3D Color Hue Management Saturation Gain Save Settings Color T1/T2/T3/T4 Temperature Primary colorMenu operation Menu systemProjector Position Front Table/Rear Table FAQ-Image and Installation FAQ-Features and Service SourceRear Ceiling/Front Ceiling Right/Bottom-leftLamp Mode Quick Cooling Off/On High Altitude Mode Audio SettingsLamp Settings Reset All SettingsDescription of each menu DisableOff AutoDynamic Color SpaceTimer display Always Timer period 15 minTimer position Top-Left Timer counting direction Count DownPower On/Off ring tone On VolumeLamp Mode Normal Reset lamp timerPicture Mode ResolutionSource Color SystemCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnglish Setup Advanced Lamp Settings Resetting the lamp timerRed IndicatorsOff Green Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartResolution Horizontal Vertical Pixel Mode Supported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputSXGA85 Supported timing for Hdmi Hdcp input1600 x 75.000 60.000 162.000 Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directiveEnglish