BenQ MP670 user manual Warranty and Copyright information, Limited warranty, Disclaimer

Page 73

Warranty and Copyright information

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in- between 10% and 85%, temperature in-between 5°C and 28°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright 2009 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

English

Warranty and Copyright information

73

Image 73
Contents MP626/MP670 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsRemote control Timer On/Set up Remote control effective rangeSource Up/ DownReplace the tray Replacing the remote control batteryChoosing a location Positioning your projectorAspect display area Display area Obtaining a preferred projected image sizeEnglish Average MP626/670 projection dimensionsConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cableConnecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesAV device Hdmi cableTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an Audio source device Audio cableTo connect the projector to an S-Video source device Connecting S-Video source devicesVideo device Audio device To connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationUsing a security cable lock Using the menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Using Auto Keystone Fine-tuning the image size and clarityCorrecting keystone Keystone functionMagnifying and searching for details Selecting the aspect ratio Playing 3D functionReal About the aspect ratioSelecting a picture mode Using Wall ColorPicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Fine-tuning the image quality in user modesAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerGo to the System Setup Basic Presentation Timer menu and press ModeHiding the image Remote paging operationsSetup Basic Panel Key Lock menu, and select Utilizing FAQ functionLocking control keys Freezing the imageUntil the System Setup Advanced menu To activate the High Altitude ModeTo highlight High Altitude Mode Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Shutting down the projector Personalizing the projector menu display3D Color Hue Management Saturation Gain Save Settings Color T1/T2/T3/T4 Temperature Primary colorMenu operation Menu systemProjector Position Front Table/Rear Table FAQ-Image and Installation FAQ-Features and Service SourceRear Ceiling/Front Ceiling Right/Bottom-leftLamp Mode Quick Cooling Off/On High Altitude Mode Audio SettingsLamp Settings Reset All SettingsDescription of each menu DisableOff AutoDynamic Color SpaceTimer display Always Timer period 15 minTimer position Top-Left Timer counting direction Count DownPower On/Off ring tone On VolumeLamp Mode Normal Reset lamp timerPicture Mode ResolutionSource Color SystemCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnglish Setup Advanced Lamp Settings Resetting the lamp timerRed IndicatorsOff Green Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartResolution Horizontal Vertical Pixel Mode Supported timing for Video and S-Video inputs Supported timing for Component-YPbPr inputSXGA85 Supported timing for Hdmi Hdcp input1600 x 75.000 60.000 162.000 Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directiveEnglish