BenQ MP670 user manual Timing of replacing the lamp, Status Message

Page 60

English

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 64 for details.

The following lamp warning displays will remind you to change the lamp.

Status

Message

The lamp has been in operation for 3500 hours.

Notice

Install a new lamp for optimal performance. If the

 

projector is normally run with Economic selected

Order Replacement Lamp

(See "Setting Lamp mode as Economic" on page

 

59), you may continue to operate the projector

Lamp > 3500 Hours

until the 3950 hour lamp warning appears.

 

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp has been in operation for 3950 hours. A

Notice

new lamp should be fitted to avoid the

 

inconvenience when the projector runs out of lamp

Replacing Lamp soon

time.

 

Lamp > 3950 Hours

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp has been in operation for 4000 hours.

Notice

It is strongly recommended that you replace the

 

lamp at this age. The lamp is a consumable item.

Replace Lamp Now

The lamp brightness diminishes with use. This is

Lamp > 4000 Hours

normal lamp behavior. You can replace the lamp

Lamp usage time exceeded

whenever you notice that the brightness level has

 

significantly diminished. If the lamp is not

Order a new lamp at lamp.benq.com

replaced beforehand, it must be replaced after

OK

4000 hours usage.

 

 

 

The lamp MUST be replaced before the projector

Notice

will operate normally.

 

 

Out of Lamp Usage Time

 

Replace lamp (Refer to user manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

60 Maintenance

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Welcome MP626/MP670 Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelDo not look straight at the projector Lens during operation. The intenseEnglish Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions ProjectorRemote control Remote control effective range Timer On/Set upSource Up/ DownReplacing the remote control battery Replace the trayPositioning your projector Choosing a locationObtaining a preferred projected image size Aspect display area Display areaEnglish MP626/670 projection dimensions AverageConnecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorWith a VGA cable With a VGA to DVI-A cableConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting Hdmi source devices To connect the projector to an Hdmi source deviceAV device Hdmi cableConnecting Component Video source devices To connect the projector to a Component Video source deviceTo connect the projector to an Audio source device Audio cableConnecting S-Video source devices To connect the projector to an S-Video source deviceVideo device Audio device Connecting Composite Video source devices To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Switching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Using Auto KeystoneCorrecting keystone Keystone functionMagnifying and searching for details Playing 3D function Selecting the aspect ratioAbout the aspect ratio RealUsing Wall Color Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant Color3D Color Management Press MODE/ENTER and the 3D Color Management page displaysSetting the presentation timer To cancel the timer, perform the following stepsGo to the System Setup Basic Presentation Timer menu and press ModeRemote paging operations Hiding the imageUtilizing FAQ function Setup Basic Panel Key Lock menu, and selectLocking control keys Freezing the imageTo activate the High Altitude Mode Until the System Setup Advanced menuTo highlight High Altitude Mode Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Muting the soundConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentPress Exit to go back to the remote network operation Press Exit to go back to the remote network operation Personalizing the projector menu display Shutting down the projectorColor T1/T2/T3/T4 Temperature Primary color 3D Color Hue Management Saturation Gain Save SettingsMenu operation Menu systemFAQ-Image and Installation FAQ-Features and Service Source Projector Position Front Table/Rear TableRear Ceiling/Front Ceiling Right/Bottom-leftQuick Cooling Off/On High Altitude Mode Audio Settings Lamp ModeLamp Settings Reset All SettingsDisable Description of each menuOff AutoColor Space DynamicTimer period 15 min Timer display AlwaysTimer position Top-Left Timer counting direction Count DownVolume Power On/Off ring tone OnLamp Mode Normal Reset lamp timerResolution Picture ModeSource Color SystemMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageDo not turn the power on with the lamp cover removed Replacing the lampEnglish Resetting the lamp timer Setup Advanced Lamp SettingsIndicators RedOff Green Troubleshooting Specifications Projector specificationsDimensions Timing chart Supported timing for PC inputResolution Horizontal Vertical Pixel Mode Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputsSupported timing for Hdmi Hdcp input SXGA851600 x 75.000 60.000 162.000 Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directiveEnglish
Top Page Image Contents