Barco R9000908 Connections, AC Power mains Cord Connection, Power Check, Switching On/Off

Page 10

Connections

3 CONNECTIONS

AC Power (mains) Cord Connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the backside of the projector.

See installation instructions before connecting to the supply.

Th is d evice co mp li es w it h part 15 of

th e FCC ru les.

Op erati on i s su bj ect to

Voir la notice d'installation avant de raccorder au réseau.

fo llo win g two co ndi tio ns (1). Th is

 

d evice may n ot cau se harmf ul i nt er -

 

f eren ce, an d ( 2) t hi s d evice mu st

 

accep t any in terf erence received

 

i nclu di ng i nt erferen ce t hat may cause

120/230 V

un desi red op erat io n"

 

 

7/5 Amp

75 Ohm

75 Ohm

50/60 Hz

 

 

PORT 4/5

PORT 2

 

7/5 Amp

50/60 Hz

Power Check

Power voltage indication on sticker on the back side of the projector. The power voltage is indicated by the art. no.

Warning !

Check if the indicated power voltage corresponds to that of the wall outlet.

Art. No. R9000901 must be connected to a 230 VAC power source. Art. No. R9000908 must be connected to a 120 VAC power source.

If the wall outlet voltage is different, call a qualified technician for power adaptation of the projector.

RS232 IN

RS232 OUT IR

REMOTE

IN RS232

OUT RS232 IR

REMOTE

Switching On/Off

The projector is switched ON and OFF using the power (mains) switch ON/OFF.

Pressed : ON

Not pressed : OFF

The projector can start now in the 'operational mode' (image dis- played) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit. This DIP switch must be set during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Stand by indication lamp :

no light up : projector switched off

green color : projector in Operational mode

red color : projector is in Standby mode.

 

 

 

This device complies with part 15 of

 

 

 

the FCC rules. Operation is subject to

 

 

 

following two conditions (1). This

 

 

 

device may not cause harmful inter-

 

 

 

ference, and (2) this device must

 

 

 

accept any interference received

VIDEO

OFF - ON

green : operation

including interference that may cause

undesired operation"

 

75 Ohm

red : standby

 

PORT 1

PROJECTOR MODE

5975007 BARCOGRAPHICS 808S 051196

 

3-1

 

Image 10
Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceOverview flowchart Service mode Starting up the Service modeService Mode Copy a block Copy ModeIdentification Graphics 808sDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cablesOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card