Barco R9000901, R9000908 owner manual From next

Page 23

Random Access Adjustment Mode

From next page

RANDOM ACCESS

ADJUSTMENT MODE

SETUP PATTERN SELECTION

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

H SIZE

VLINEARITY

V SIZE

BLANKING

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

RED

GREEN

BLUE

RED

GREEN

BLUE

RED AND GREEN

BLUE AND GREEN

RED AND BLUE

TOP

BOTTOM

LEFT

RIGHT

CONTRAST MODULATION

SOFT EDGE CORRECTION

6-2		5975007 BARCOGRAPHICS 808S 051196

Image 23

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn repacking On installationOn cleaning On servicingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Connections AC Power mains Cord ConnectionPower Check Switching On/OffStart up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. VideoInput selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selectionRGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input SelectionTo select the component video input Connecting a Component Video source to port 4/5Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCUUsing your RCU How to use your RCUHardware set up of the projector address How to control the projectorInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Seagull CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentService Mode Starting up the Service modeOverview flowchart Service mode Graphics 808s Copy ModeIdentification Copy a blockDeletion of all blocks Delete ModeDeletion of blocks Deleting block by blockBarcographics 808s Change passwordChange Language Run timeUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication ErrorOptions Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card