Barco R9000908, R9000901 owner manual Connecting a Component Video source to port 4/5

Page 14

Connections

Connecting a RGB Analog source with Tri-level sync to port 4/5.

(option)

RGB analog input terminals with Tri level sync input or with Tri-level sync on green. The projector detects automatically where the sync signal is located.

See installa tion ins tructions befor e conne cting to the supply.

Voir la notice d'installation avant de raccorder au réseau.

12 0/2 30 V	7 5 Ohm	7 5 Ohm
7/5 Amp

50/60 Hz
PORT 4/5	POR T 2

This device complies with p art 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cau se harmful inter- ference, and (2) this device must accept an y interference r eceived including interference that may cause undesired operation"

RGB input selection :

(RG3sB : R, G, B signals with automatic Tri-level sync detection)

with the RCU or the build in RCU : press digit button 7

VCR HDTV player

Audio amplifier

798

Connecting a Component Video source to port 4/5.

Acomponent video (R-Y, Y, B-Y) with sync signals can be connected to the projector via the Port 4/5. The projector detects automatically where the sync signal is located.

See installa tion ins tructions befor e conne cting to the supply.

Voir la notice d'installation avant de raccorder au réseau.

12 0/2 30 V	7 5 Ohm	7 5 Ohm
7/5 Amp

50/60 Hz
PORT 4/5	POR T 2

This device complies with p art 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cau se harmful inter- ference, and (2) this device must accept an y interference r eceived including interference that may cause undesired operation"

To select the component video input :

with the RCU or the build in RCU : press digit button 6.

VCR HDTV player

Audio amplifier

798

Connecting a Component Video source with Tri- level sync to port 4/5.

(Opion)

Acomponent video (R-Y, Y, B-Y) with Tri-level sync signals can be connected to the projector via the Port 4/5. The projector detects

automatically where the sync signal is located.

See installa tion ins tructions befor e conne cting to the supply.

Voir la notice d'installation avant de raccorder au réseau.

12 0/2 30 V	7 5 Ohm	7 5 Ohm
7/5 Amp

50/60 Hz
PORT 4/5	POR T 2

This device complies with p art 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cau se harmful inter- ference, and (2) this device must accept an y interference r eceived including interference that may cause undesired operation"

To select the component video input :

with the RCU or the build in RCU : press digit button 8.

VCR HDTV player

Audio amplifier

798

5975007 BARCOGRAPHICS 808S 051196		3-5

Image 14

Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceService Mode Starting up the Service modeOverview flowchart Service mode Copy a block Copy ModeIdentification Graphics 808sDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cablesOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card