Barco R9000908, R9000901 Blanking Adjustments, Top blanking Right blanking Bottom blanking

Page 36

Random Access Adjustment Mode

Blanking Adjustments

Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking.

To start up the Blanking adjustments, follow the next procedure :

Push the control stick forward or backward to highlight BLANKING on the Geometry menu and then press ENTER.

GEOMETRY

 

H PHASE

 

RASTER SHIFT

 

LEFT-RIGHT (E-W)

 

LEFT SIDE CORRECTION

 

TOP-BOTTOM (N-S)

 

H SIZE

 

V LINEARITY

 

V SIZE

 

BLANKING

 

BLANKING

 

TOP

 

BOTTOM

 

LEFT

 

RIGHT

 

Select with

or

then <ENTER>

<EXIT> to return.

The following blanking corrections are possible :

-top blanking

-bottom blanking

-left blanking

-right blanking

Left blanking

Therefore :

-if the internal # pattern was selected, this pattern remains on the screen.

-if the genlocked pattern was selected, the external source

will be displayed.

Adjust the next blanking alignments until the image is correctly framed or the unwanted information is blanked out.

To enter a blanking alignment, push the control stick forward or backward to highlight a function and press ENTER to activate this function.

Press EXIT to return.

Top blanking

Right blanking

Bottom blanking

Adjustment of the blanking on the of the image

BLANKING

TOP

 

BOTTOM

 

LEFT

 

RIGHT

 

Select with

or

then <ENTER>

 

<EXIT> to return

Adjustment of the blanking on the bottom of the image

Correct by pushing the control stick forward or backward

Adjustment of the blanking on the left side

Adjustment of the blanking on the right side

Correct by pushing the control stick to the right or to the left

5975007 BARCOGRAPHICS 808S 051196

 

6-15

 

Image 36
Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn installation On cleaningOn servicing On repackingLocation and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsSignal Input Connection to the Projector Port No Projector input Press Digit ButtonComp. Video Video1/Comp. Video Start up with full white imageConnecting a Composite Video source to port Connecting a S-Video or Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5Analog Input Selection RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to use your RCU Hardware set up of the projector addressHow to control the projector Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Port 2 Video or S-Video Line Doubler optionColor Select Color SelectFocusing Geometry Adjustments Horizontal Phase AdjustmentGeometry GeometryRaster Shift Adjustment Projected rasterCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Seagull correction Left Side CorrectionSeagull Correction Left Side CorrectionTop-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceStarting up the Service mode Overview flowchart Service modeService Mode Copy Mode IdentificationCopy a block Graphics 808sDelete Mode Deletion of blocksDeleting block by block Deletion of all blocksChange password Change LanguageRun time Barcographics 808sSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle CRT Drive Mode Projector Warm UpProjector Warm UP Projector Warm UPMESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available I2C error Addr FH3 RWI commu Nication ErrorIris commu Nication Error Invalid RWI soft VersionOptions Magik Interface Ceiling Mount kit CM100 Orbiting KitLine Doubler Kit Adapter and communication cablesOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card