Barco R9000908, R9000901 owner manual Adjustment Blocks and Source Numbers

Page 54

Adjustment Blocks and Source Numbers 90-99

The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source number is selected, the alternate block of adjustment data is in use and may be modified via the adjust mode of the projector. The alternate adjustment block is automatically stored.

Follow the steps below to create a second adjustment block for a source between 0 and 9.

1.Select the source between 0 and 9 that the second adjustment block is to be created for.

2.Select the corresponding source number between 90 and 99. The adjustment block for the source number between 0 and 9 is copied to the corresponding source number between 90 and 99.

3.Enter the adjust mode and make any desired changes (geometry, convergence, sync fast/slow, enhanced blue on/off) to the second adjustment block.

4.Exit the adjust mode.

Note : the above also applies to source number 1 - 5 and 91 - 95 of a stand alone projector (no RCVDS)

B-2		5975007 BARCOGRAPHICS 808s 160996

Image 54

Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceStarting up the Service mode Overview flowchart Service modeService Mode Copy a block Copy ModeIdentification Graphics 808sDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPMESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cablesOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card