Barco R9000908, R9000901 owner manual Location and Function of Controls

Page 8

Location and Functions of Control

2

 

LOCATION AND FUNCTION OF CONTROLS

 

 

 

 

 

 

 

 

 

 

 

 

REAR PANEL TERMINOLOGY

See installation i nstructions before connecting to the supply.

Voir la notice d'installation avant de raccorder au réseau.

120/230 V

 

 

7/5 Amp

7 5 Ohm

75 Ohm

50/60 Hz

 

 

PORT 4/5

PORT 2

 

This device co mplies with part 15 of the FCC rules. Oper ation is sub ject to following two conditions ( 1). This device may no t cause h armful inter- feren ce, and (2) this device must accep t any in terferen ce received including interference that may cause undesired operation"

1 2 3 4 5 6 7 8 9 10

1

Power Switch : press the switch to turn the projector ON.

6

Depending on the hardware set-up of the projector during

 

 

 

installation, the projector switches to ‘Standby’ or to ‘Opera-

7

 

tional'mode. If in standby, the standby LED lights up.

2

AC Power Input

8

 

 

 

3

Communication Port (800 peripherals)

 

* allows communication between the RCVDS switcher and

 

 

the projector.

 

9

 

* allows connection of a remote IR receiver unit to the

 

projector.

 

 

4

Port 3

 

10

RGB Analog Input (9 pin female sub D connector). Allows a

 

 

character generator, microcomputer, etc. having analog RGB

 

 

outputs to be connected to the projector.

 

5

Port 4/5 : RGB-S Input (5x BNC connector):

 

RGB-S input : allows a character generator, microcomputer,

 

 

video camera, etc. having analog RGB output to be con-

 

 

nected to the projector.

 

 

Line inputs:

- signals RED-GREEN-BLUE

 

 

 

- COMPOSITE sync. signal

 

 

 

- Tri level sync signal (option)

 

S-VIDEO Input: Separated Y/C (luma-chroma) signal inputs and outputs for higher quality playback of Super VHS signals (4-pin S-VIDEO connector loop-through).

75 ohm Termination Switch for S-Video signals

VIDEO Input (Composite video, 2x loop-through BNC connector): allows a video tape recorder, video camera, color receiver/monitor, etc. having video line output to be connected to the projector.

75 ohm Termination Switch for Video signals

Projector Pilot Lamp : indicates the status of the projector.

-unlit : mains (power) switch is not pressed.

-lit : mains (power) switch is pressed and the indicated color shows the projector mode:

Green color : operational mode of the projector.

Red color : standby mode of the projector.

Important : projector ("Operational" or "Standby") mode is defined during the installation of the projector. (Refer to a qualified technician for change).

FRONT PANEL TERMINOLOGY

RS232 IN

RS232 OUT IR

REMOTE

IN RS232 OUT RS232 IR

REMOTE

11

12

13

14

11

12

RS 232 Input Port

Connection between the BARCOGRAPHICS 808 and an IBM PC (or compatible) or MAC (RS422) for remote computer control and data communication.

RS 232 Output Port

RS 232 Input Port allows a communication link for PC or MAC to the next projector in a series of projector.

13

14

IR Sensor

receiver for control signals transmitted from the RCU.

IR Remote

Connector for remote input for hard wired remote control

5975007 BARCOGRAPHICS 808S 090996

 

2-1

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn installation On cleaningOn servicing On repackingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsSignal Input Connection to the Projector Port No Projector input Press Digit ButtonComp. Video Video1/Comp. Video Start up with full white imageConnecting a Composite Video source to port Connecting a S-Video or Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5Analog Input Selection RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Battery installation in the RCU ControllingHow to use your RCU Hardware set up of the projector addressHow to control the projector Using your RCUInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Port 2 Video or S-Video Line Doubler optionColor Select Color SelectFocusing Geometry Adjustments Horizontal Phase AdjustmentGeometry GeometryRaster Shift Adjustment Projected rasterCrt faceplate border Raster ShiftLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Seagull correction Left Side CorrectionSeagull Correction Left Side CorrectionTop-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceService Mode Starting up the Service modeOverview flowchart Service mode Copy Mode IdentificationCopy a block Graphics 808sDelete Mode Deletion of blocksDeleting block by block Deletion of all blocksChange password Change LanguageRun time Barcographics 808sSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections CRT Drive Mode Projector Warm UpProjector Warm UP Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz I2C error Addr FH3 RWI commu Nication ErrorIris commu Nication Error Invalid RWI soft VersionOptions Magik Interface Ceiling Mount kit CM100 Orbiting KitLine Doubler Kit Adapter and communication cablesOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents