Barco R9000908 How to display a projector address?, How to program an address into the RCU?

Page 18

Controlling

How to display a projector address?

With the digit buttons on the RCU, it is possible to select input sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S.

Press the ADDRESS key (recessed key on the RCU) with a pencil.

The projector's address will be displayed in a 'Text box'. This text box When a valid and available source is selected, there will be informa- tion displayed on the screen about that source (if "Text" is on). This information includes :

-source number

- horizontal frequency - vertical frequency

PROJECTOR ADDRESS 001

disappears after a few seconds.

 

To continue using your RCU, it is necessary to enter the same

Source 2

Fh= 15.6 kHz

address with the digit buttons (address between 0 and 9). For

Fv= 50 Hz

exemple, if the Adrress Key displays projector address 003, then

 

press the "3" digit button on the RCU to set the RCU's address to

match the projector's address.

When the entry is a non valid source

number, a warning appears on the screen : 'input not available'.

How to program an address into the RCU?

Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons. That address can be any digit between 0 and 9.

When programming '0', zero address, the RCU will control a projector regardless of the projector's address. This feature allows multiple projectors with different addresses to be controlled by a single RCU.

Input selection

Port No

Projector input

Press Digit

 

 

 

 

Button

 

 

 

 

 

1

Comp. Video

1

 

2

S-Video1/Comp. Video*

2

 

3

RGB2

3

 

4/5

RGB2

4 or 5

 

4/5

Component video3

6

 

 

 

 

 

 

 

4/5

RGB with Tri level sync4

7

 

 

4/5

Component video

 

 

 

 

with Tri-level sync5

8

 

 

 

 

 

 

Only available when the optional Tri-level sync module is installed.

1Input signal Y/C (luma/chroma)

2Input signal : R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate Hor and Vert. sync) or sync on green (composite sync).

3Input signal : R-Y, Y and B-Y with separate composite sync or with separate Hor and Vert.sync or with composite sync on Y.

4Input signal : R, G and B with separate Tri level sync or with Tri- level sync on green.

5Input signal : R-Y, Y and B-Y with separate Tri level sync or with composite Tri-level sync.

* Video or S-Video : switchable in the PictureTuning menu.

WARNING

input not available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source

WARNING

source not available

becomes available. A message 'source not available' will be dis- played for a short time.

5975007 BARCOGRAPHICS 808sS 160996

 

4-3

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceStarting up the Service mode Overview flowchart Service modeService Mode Copy a block Copy ModeIdentification Graphics 808sDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPMESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cablesOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents