Barco R9000901 Invalid RWI soft Version, I2C error Addr FH3, Short Circuit on I2C bus, Starting

Page 47

Messages, warnings and failure codes

WARNING :

go to

stand by

WARNING :

invalid

frequency

input

WARNING :

default settings loaded in the E2PROM

table is deleted

FAILURE

invalid

RWI soft

version

FAILURE

I2C error

addr. : 7FH3

FAILURE

short

circuit on I2C bus

Projector will switch to 'stand-by'when the RCVDS is no longer available.

The entered frequency or ap- plied frequency of the source is out of the projector's range.

Adjustment settings are lost. Re- load using Projector Control Soft- ware via PC or MAC (if this op- tion is available), or readjust im- age.

Message to inform that selected table is deleted. This message will be followed by 'confirm mes- sage', on which the user has to answer.

Wrong software version in your projector. Call for technical sup- port.

Hardware failure. Call a quali- fied service technician for repair.

Hardware failure. Call a quali- fied service technician for repair.

FAILURE

RCVDS com- munication error

FAILURE

RWI commu-

nication

error

FAILURE

IRIS commu-

nication

error

WAIT

starting

up

IRIS

Serial communication error be- tween RCVDS800 and projec- tor.

Hardware failure. Call a quali- fied service technician.

Communication error between IRIS 800 and the projector. Call a qualified service technician.

Message during the start up of the IRIS 800. Message will dis- appear when the IRIS 800 is ready to accept commands.

8-2		5975007 BARCOGRAPHICS 808s 160996

Image 47

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn repacking On installationOn cleaning On servicingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Connections AC Power mains Cord ConnectionPower Check Switching On/OffStart up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. VideoInput selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selectionRGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input SelectionTo select the component video input Connecting a Component Video source to port 4/5Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCUUsing your RCU How to use your RCUHardware set up of the projector address How to control the projectorInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Seagull CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentService Mode Starting up the Service modeOverview flowchart Service mode Graphics 808s Copy ModeIdentification Copy a blockDeletion of all blocks Delete ModeDeletion of blocks Deleting block by blockBarcographics 808s Change passwordChange Language Run timeUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication ErrorOptions Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card