Barco R9000908 MESSAGES, Warnings and Failure Codes, Fh= 15.6 kHz Fv= 050 Hz, Input not available

Page 46

Messages, warnings and failure codes

8 MESSAGES, WARNINGS AND FAILURE CODES

SOURCE 01

Fh= 15.6 kHz

Fv= 050 Hz

SOURCE 01

Fh= 15.6 kHz

Fv= 050 Hz

enter

password

xxxx

text on

text off

PROJECTOR

ADDRESS :

003

WARNING :

input not available

When selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical frequencies of the dis- played source.

Announcement of the selected source.

Message to enter your password. Password contains 4 digits.

These messages will be dis- played on the screen when push- ing the <TEXT> key.

Text ON : the 'bar scale indica- tion' will be enabled during the change of an analog control in the 'operational mode' + all warn- ings and failures will be displayed.

Text OFF : the 'bar scale indica- tion' will be disabled during the change of an analog control in the 'operational mode' + all warn- ings and failures will not be dis- played.

Indication of the projector ad- dress when activating the 'AD- DRESS' button on the RCU with a pencil or other small object.

When using the projector with the RCVDS, this warning will be displayed when selecting an in- put slot of an RCVDS where the input board is missing.

WARNING :

source not

available

WARNING :

invalid

key entry

WARNING :

invalid

code entry

WARNING :

end of ad- just range

WARNING :

input no

longer

available

check input signal

or select

new source

WARNING :

input selector

not

available

The input is a valid input but the source is not connected to the input terminals or the input source is switched off.

When a wrong key is pressed on the RCU.

Message when the entered pass- word is wrong.

End of adjustment range.

Message will be displayed when the input source is no longer available. The following message then appears: 'check input sig- nal or select new source'.

This message will be displayed after the message 'input no longer available'. It asks to check the connections between the source and the projector or to check if the source is switched on.

It warns you to check the power connection or the power status of the RCVDS.

Next message will appear imme- diately on the screen : 'go to stand-by'.

5975007 BARCOGRAPHICS 808s 160996		8-1

Image 46

Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceOverview flowchart Service mode Starting up the Service modeService Mode Copy a block Copy ModeIdentification Graphics 808sDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cablesOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card