Barco R9000908, R9000901 owner manual Adjustment procedure multiple projector installations

Page 52

Orbiting

Adjustment procedure multiple projector installations :

Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum.

Default setting of the Master projectorn see 'Stand-Alone projector'.

Highlight 'ADJUST DEVIATION' by pushing the control stick forward or backward and press ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation adjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH	OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH	OR
HORIZONTAL WITH	OR
<EXIT> to return.

HORIZONTAL

ORBIT AMPL

70

VERTICAL

ORBIT AMPL

70

5975007 BARCOGRAPHICS 808s 160996		A-3

Image 52

Contents Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn installation On cleaningOn servicing On repackingLocation and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsSignal Input Connection to the Projector Port No Projector input Press Digit ButtonComp. Video Video1/Comp. Video Start up with full white imageConnecting a Composite Video source to port Connecting a S-Video or Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5Analog Input Selection RGB input selectionConnecting a Component Video source to port 4/5 To select the component video inputConnecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU ControllingHow to use your RCU Hardware set up of the projector addressHow to control the projector Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Port 2 Video or S-Video Line Doubler optionColor Select Color SelectFocusing Geometry Adjustments Horizontal Phase AdjustmentGeometry GeometryRaster Shift Adjustment Projected rasterCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull correction Left Side CorrectionSeagull Correction Left Side CorrectionTop-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Adjustment ConvergenceOverview flowchart Service mode Starting up the Service modeService Mode Copy Mode IdentificationCopy a block Graphics 808sDelete Mode Deletion of blocksDeleting block by block Deletion of all blocksChange password Change LanguageRun time Barcographics 808sSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle CRT Drive Mode Projector Warm UpProjector Warm UP Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available I2C error Addr FH3 RWI commu Nication ErrorIris commu Nication Error Invalid RWI soft VersionOptions Magik Interface Ceiling Mount kit CM100 Orbiting KitLine Doubler Kit Adapter and communication cablesOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card