Barco R9000901, R9000908 owner manual Top-Bottom north-south Adjustments, Top-Bottom N-S

Page 33

Random Access Adjustment Mode

Top-Bottom (north-south) Adjustments

Top-Bottom and center adjustments affect only the horizontal lines of the projected image.

To start up the Top-Bottom and center corrections, follow the next procedure :

Push the control stick forward or backward to highlight TOP-BOT- TOM (N/S) on the geometry menu and then press ENTER.

Only the green image is displayed while making top-botton adjust- ments. The red and blue images will automatically be corrected in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.

The following adjustments can be executed :

-horizontal centerline bow

-horizontal centerline skew

-top bow

-top keystone

-bottom bow

-bottom keystone

-seagull correction

All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100.

Adjust the next alignments until the vertical lines are straight.

To enter an alignment, push the control stick forward or backward to highlight a function and press ENTER to activate this function. Press EXIT to return.

TOP-BOTTOM

H CENTERLINE BOW

H CENTERLINE SKEW

TOP BOW

TOP KEYSTONE

BOTTOM BOW

BOTTOM KEYSTONE

SEAGULL CORRECTION

Select with or

then <ENTER> <EXIT> to return.

GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
Select with	or
then <ENTER>
<EXIT> to return.

Corrects for curvature of the horizontal lines in the middle of the image.

Corrects the tilting of the horizontal lines in the middle of the image.

Corrects for curvature of the horizontal lines on the upper side

Corrects the keystone geometry correction of the hor. lines on the upper side

Corrects for curvature of the horizontal lines on the lower side

Corrects the keystone geometry correction of the hor. lines on the lower side


	Correct by pushing		Correct by pushing
	the control stick		the control stick
	backward		forward
6-12		5975007 BARCOGRAPHICS 808S 051196
6-12		5975007 BARCOGRAPHICS 808S 051196

Image 33

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPort No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white imageConnecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selectionTo select the component video input Connecting a Component Video source to port 4/5Connecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUHow to control the projector Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Line Doubler option Port 2 Video or S-VideoColor Select Color SelectFocusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Left Side Correction Seagull correctionSeagull Correction Left Side CorrectionTOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentStarting up the Service mode Overview flowchart Service modeService Mode Identification Copy ModeCopy a block Graphics 808sDeletion of blocks Delete ModeDeleting block by block Deletion of all blocksChange Language Change passwordRun time Barcographics 808sUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UPMESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik Interface Ceiling Mount kit CM100Line Doubler Kit Adapter and communication cablesOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card