Barco R9000901, R9000908 Change password, Change Language, Run time, Barcographics 808s, RUN Time

Page 41

Service Mode

Change password

This item is password protected.

Highlight 'change password' with the control stick and press ENTER.

The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control stick to the left or to the right to select the digits to be changed. Use the numeric keys to enter the new digits.

Press ENTER to save the new password. Before saving the new password, a confirmation screen will be displayed.

Press EXIT to return to the Service menu without saving the new password.

When the displayed password is correct, press ENTER to save. If not correct, press EXIT to cancel the saving.

SERVICE MODE

IDENTIFICATION

COPY A BLOCK

DELTE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUN TIME

SET TO MIDPOSITION

CONVERGENCE MID

DYNAMIC ASTIGMATISM

MORE...

PASSWORD

Enter new password :

0 0 0 0

Use and to select, and reprogram

with numeric keys.

CHANGE PASSWORD

Password will be reprogrammed as xxxx

<ENTER> to confirm <EXIT> to cancel

Change Language

The 'Change Language' function offers the possibility to change the language of the screen menus to :

-English

-Spanish

-French

-German

therefore, pusj the control stick forward or backward to highlight 'Change language' and pressENTER to select the language menu.

Push the control stick forward or backward to select the desired language and press ENTER to change the language.

Run time

Highlight 'run time' with the control stick and press ENTER to display the amount of time the projector has played since its first start up at the factory.

Note : all projectors leave the factory after a burn-in period of approximately 100 hours.

Press EXIT to return the service mode menu.

7-4

SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select
then	LANGUAGE
<EXIT>	LANGUAGE

ENGLISH

ESPAÑOL

FRANCAIS

DEUTSCH

Select new language

with or then <ENTER> <EXIT> to return.

SERVICE MODE

IDENTIFICATION

COPY A BLOCK

DELTE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUN TIME

SET TO MIDPOSITION

DYNAMIC

RUN TIME

105 h

5975007 BARCOGRAPHICS 808s 160996

Image 41

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPort No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white imageConnecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selectionTo select the component video input Connecting a Component Video source to port 4/5Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUHow to control the projector Using your RCUInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Line Doubler option Port 2 Video or S-VideoColor Select Color SelectFocusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionSeagull Correction Left Side CorrectionTOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentService Mode Starting up the Service modeOverview flowchart Service mode Identification Copy ModeCopy a block Graphics 808sDeletion of blocks Delete ModeDeleting block by block Deletion of all blocksChange Language Change passwordRun time Barcographics 808sUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik Interface Ceiling Mount kit CM100Line Doubler Kit Adapter and communication cablesOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card