Barco R9000901, R9000908 owner manual Convergence Adjustment

Page 37

Random Access Adjustment Mode

Convergence Adjustment

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image.

Note : the green convergence adjustments can be added as an option. When these are available, always start with 'green only'. This option will also be indicated on the convergence menu.

Highlight first 'Green only' when available with the control stick and press ENTER to display the convergence adjustment menu

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

CONTR. MODULATION

SOFT EDGE

CONVERGENCE

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

CONVERGENCE

SEL : select area

using

arrow keys

ADJ : adjust area

using

arrow keys

Toggle between SEL and ADJ with <ENTER> <ENTER> continue <EXIT> to return

The screen area is divided into 25 areas. Use the control stick to move the box to the desired zone and then press ENTER to begin the convergence adjustment. Start the convergence adjustment with zone one and continue as mentioned in the diagram hereafter.

Use the control stick to make horizontal or vertical convergence adjustments in the selected zone and then press ENTER to move the box to another zone or EXIT to return to the Convergence menu.

ENTER toggles arrow keys between zone selection and zone adjust- ment .

EXIT returns to convergence menu

25 23 9 15 17

24 22 8 14 16

5

4

1

2

3

20 18 6 10 12

21 19 7 11 13

CONVERGE ADJUSTMENT

70

green image

red image

6-16		5975007 BARCOGRAPHICS 808S 051196

Image 37

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPort No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white imageConnecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selectionTo select the component video input Connecting a Component Video source to port 4/5Connecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUHow to control the projector Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Line Doubler option Port 2 Video or S-VideoColor Select Color SelectFocusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Left Side Correction Seagull correctionSeagull Correction Left Side CorrectionTOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentOverview flowchart Service mode Starting up the Service modeService Mode Identification Copy ModeCopy a block Graphics 808sDeletion of blocks Delete ModeDeleting block by block Deletion of all blocksChange Language Change passwordRun time Barcographics 808sUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik Interface Ceiling Mount kit CM100Line Doubler Kit Adapter and communication cablesOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card