Barco R9000901, R9000908 owner manual Vertical Linearity Adjustment, Vertical Size Adjustment

Page 35

Random Access Adjustment Mode

Vertical Linearity Adjustment

The vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image.

Push the control stick forward or backward to highlight V LINEARITY on the Geometry menu and then press ENTER.

ENTER will select vertical linearity adjustment,

EXIT returns to random access adjustment mode menu, ADJUST returns to operational mode

Adjust the vertical linearity with the control stick until the distances between the horizontal lines of the set up pattern are equal from top to bottom.

EXIT will return to the Geometry menu

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

V LINEARITY

70

Vertical Size Adjustment

Push the control stick forward or backward to highlight V SIZE on the Geometry menu and then press ENTER.

ENTER will select vertical size adjustment

EXIT returns to random access adjustment mode menu,.

ADJUST returns to operational mode

Adjust the vertical size by pushing the control stick forward or backward until the correct image height is obtained.

Note :

-if the internal # pattern was selected, this pattern remains on the screen.

-if the genlocked pattern was selected, the external source will be displayed.

A bar scale and a numeric indicator give a visual indication of the vertical size adjustment.

Hint : In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small vertical size setting.

EXIT will return to Geometry

Ideal

Image

Hight

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

V SIZE

70

		Ideal
	Image too
			Image too
		Image	Image too
	Tall	Hight	Short

6-14		5975007 BARCOGRAPHICS 808S 051196

Image 35

Contents Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn repacking On installationOn cleaning On servicingLocation and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Connections AC Power mains Cord ConnectionPower Check Switching On/OffStart up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. VideoInput selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selectionRGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input SelectionTo select the component video input Connecting a Component Video source to port 4/5Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCUUsing your RCU How to use your RCUHardware set up of the projector address How to control the projectorInput selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Seagull CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsConvergence Convergence AdjustmentService Mode Starting up the Service modeOverview flowchart Service mode Graphics 808s Copy ModeIdentification Copy a blockDeletion of all blocks Delete ModeDeletion of blocks Deleting block by blockBarcographics 808s Change passwordChange Language Run timeUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication ErrorOptions Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card