LG Electronics AVS2400 owner manual Viewing Call Statistics, Ending a Call

Page 62

62Operation

4

Operation

Viewing Call Statistics

To view statistical information about a call, follow these steps:

1.During a call, press the button.

2.Audio and video statistics for the current call appear on the screen.

Two columns of statistics, Receive and Transmit appear. The total bandwidth used for audio and video appear alongside each column heading. Each column has a video and audio block.

•Video statistics include the following:

-- resolution shows the resolution, in pixels, of the video image transmitted or received. -- codec shows the video codec used to compress and decompress the video.

-- bandwidth shows the amount of video data transferred per second in kilobits. -- frame rate shows the video frame rate in frames per second.

•Audio statistics include the following:

-- codec shows the audio codec used to compress and decompress the audio. -- bandwidth shows the amount of audio data transferred per second in kilobits.

-- packet rate shows the amount of audio data packets transferred or received per second in kilobytes.

•Both the Audio and Video block include the following:

-- jitter shows the variation, in milliseconds, in the time between packets arriving, caused by network congestion, timing drift or route changes.

-- packet loss shows the number of packets of data that fail to reach their destination. Packet loss can be caused by a number of factors, including signal degradation over the network medium, oversaturated network links, corrupted packets rejected in-transit, faulty networking hardware, maligned system drivers or network applications, or normal routing routines.

-- cumulative shows the up to date count of packets lost in the call.

-- percentage shows packet loss as a percentage of the total packets sent.

•The following additional information appears below the Audio statistics block: -- the call duration

-- the make and model of the far end video communication device and the software version it is using -- the call protocol (H.323 or SIP, for example)

3.To hide the statistics, press the button again. Statistics automatically refresh every 5 seconds and hide after 5 minutes.

Ending a Call

You can end a call using any of the following options:

•hang up button on the remote control

•Call Manager dialog

•REDIAL list

Ending a Call from the Call Manager

To hang up a call from the Call Manager dialog, follow these steps:

1.From any call screen, press OK. The Call Manager dialog appears.

2.To hang up a call, press OK again to end the call.

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Video Conference Monitor Safety Information Regulatory Information FCC PartLamps Contain Mercury, Dispose Properly Disposal of your old applianceEEE Compliance with Directive. for Turkey only Or moisture, does not operate normally, or has been droppedOn Safety On InstallationOn Disposal On CleaningOn Repacking Lifting and moving the VCSContents Mode settings Customizing OSD settingsMenu settings SpecificationsFeatures IntroductionVCS Body Remote control and batteries UnpackingOverview Front of the VCSOSD lock / unlock function Power cord Inlet AC in Connects the power plugRear of the VCS Remote Control Battery InstallationConnections Attaching the standUsing the Kensington security system optional Disassembling the standAudio Connecting to a PCVideo Hdmi connectionSUB connection Connecting Network Connecting PowerConnecting Headphones Connecting a MicrophoneAdjusting the angle of the Monitor and camera Attaching the back coverInitial settings for VCS Default administrator password is 1 2 3Set the options of the Identification menu and press Set the options of the Network menu and press button Installation Main screen overview Icon Accessing the System Menu User Preferences setup Access User Preferences from which you can do the followingAdministration Using the Remote Control Administrator PreferencesAccessing Administrative Features Administration from a Web BrowserInstallation Configuring Call Preferences Admission Control Configuring Security PreferencesControlling Remote Administration Changing the Administrator Password Setting the User PasswordConfiguring Audio Codec Order Viewing Recent Configuration ChangesConfiguring Audio Behaviors Adjusting Audio Levels Administrator Preferences AudioTesting Primary Audio Output Selecting the Active MicrophoneSpecifying the Hostname and Domain Name Service DNS Servers Configuring Network UsageSpecifying a Locally Configured IP Address Specifying Network SpeedEnabling IPv6 Addressing Specifying a Vlan TagSpecifying an NTP Server Enabling Network Address Translation NAT Restricting Reserved PortsCall Type Number of Required UDP and TCP Ports Configuring Quality of ServiceConfiguring LifeSize Transit Preferences Call Type Number of Required UDP PortsDisabling Access to the Local Directory Populating the Corporate DirectoryReading from an Ldap Server Ldap preferences are not configuredConfiguring Auto Discovery Server and receive data was successfulConfiguring Communications Preferences Enabling TelepresenceReceiving Presentations Configuring Dialing OptionsSpecifying H.323 Settings Virtual Link Data SharingConfiguring SIP Settings Enabling H.460 Support for H.323 CallsConfiguring Appearance Preferences Video Layout PreferencesLocking the Camera Presets Configuring Video BehaviorsConfiguring Display Preferences Controlling the Camera Use by Far End UsersAdjusting the MTU of Video Packets Configuring System SettingsAdjusting Video Encoder Quality Selecting Priority of Quality Metrics for Source VideoNavigate to Administrator Preferences System License Keys Rebooting the System automaticallyManually Setting System Date and Time Identifying the SystemHours to complete Installing a License Key ManuallyNavigate to Preferences System License Keys Using Diagnostics Preferences and Tools Restoring Default SettingsRebooting the System Using Camera Diagnostic PreferencesUsing Network Utilities Do Not Disturb Saving and Restoring a System Configuration Exclusive Web Administration FeaturesUsing Advanced Directory Features Upgrading System Software Copying Screen Text to the ClipboardDownloading Call History Upgrading your System Software Managing Calls from the Web Administration InterfaceTroubleshooting Upgrade Failures Upgrade Error Codes Placing a Call from the Redial List Near End Video QualityPlacing a Call To place a call from the directory, follow these steps Placing a Call from the DirectoryManually Dialing a Number from the Main Screen Manually Dialing a Video NumberAnswering or Rejecting a Call Manually Dialing a Voice NumberCall Status Using System Do Not DisturbManaging a Call Caller IDManaging PIP Hiding or Showing User Interface ElementsManaging Audio Managing Video LayoutFar End Video Near End Video Screen Layout Far End VideoNear End Video Far End Video Near End Video During aEnding a Call from the Call Manager Viewing Call StatisticsEnding a Call To hang up a call, press OK again to end the callRemoving an Entry from the Redial List Managing the Redial ListLocking and Unlocking Entries in the Redial List Adding a Redial List Entry to the DirectoryCopying an Entry from the Corporate to the Local Directory Managing the DirectoryAdding an Entry to the Local Directory Removing an Entry from the Local DirectoryEditing an Entry in the Local Directory Adding an Entry to the Meetings DirectoryNavigation button overview Customizing OSD settingsMenu settings Supported Input Description Mode settings Please contact the service center Check the power cable is connected correctlyCheck the main power switch is turned on Check the input voltage is correctYou can not make a call Configure your display againConnected. Check the signal cable and try again Appears on the screenSpecifications Diagnostic logging 280 x720p @ 25 to 30 fps ResolutionDo Not Disturb mode Directory Service H.350Admin and User level password Save, Lock, Remove Redial List featuresBackup and Restore capability Ability to disable HTTP, SSH and Telnet servicesWarranty Card Appendix
Top Page Image Contents