Planar PR9020 user manual Power on/off, Turning on the power, Turning off the power

Page 18
Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for about 5 seconds.
Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

Power on/off

Power on/off

Turning on the power

1.

2. Remove the lens cover, and set the power switch to the ON position (marked “ I “).

The power indicator will light up in steady orange (67). Then wait several seconds because the buttons may not function for these several seconds.

3. Press the STANDBY/ON button on the projector or the remote control.

STANDBY/ON button

POWER indicator

Power switch

The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green. To display the picture, select an input signal according to the section "Selecting an input signal" (18).

Turning off the power

1.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position (marked “O“).

The POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

•When the AUTO ON of the OPTION menu is set to the TURN ON, and the power was turned off by the power switch last time, turning the power switch on makes the projection lamp light on without pushing the STANDBY/ON button (42).

•Use the shutdown switch (69) only when the projector is not turned off by normal procedure.

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PR9020 LCD Projector Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Contents of package Fastening the lens coverHOT Part namesProjector HOTControl port &10 Hdmi port &10 Control panelRear panel Video port &10Remote control Back Remote controlLaser pointer &13 It is a beam outlet Setting up Surface ArrangementOn a horizontal Suspended from the ceilingAdjusting the projectors elevator Using the security bar and slotMonitor Connecting your devicesUSB storage SD card Remote control Speakers wiht an amplifierConnecting your devices About Plug-and-Play capabilityConnecting power supply AC inlet Connector of the power cord To the outletPutting batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Front and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicator Power switchOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalSelecting an input signal  For an Hdmi signalUsing the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Enter buttonAuto Picture ModeAspect KeystoneEasy Menu Picture Menu GammaPicture Menu Color TempMY Memory Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4Image Menu Over ScanPosition Image Menu PhaseAuto Adjust SizeInput Menu Video Format Input MenuComponent HdmiDescription Resolution Setup Menu Setup Menu Audio Menu Screen Menu Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Or keep no operation for about 10 secondsScreen Menu Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageLens Type Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordSecurity Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeDescription Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network MenuNetwork Menu Projector NameEnter or Input button Description Shot To switch the image displayedPress the or ESC button on the remote control Use the / buttonsInformation Lamp MaintenanceCase of replacement by yourself Part number =Lamp warning LampCleaning the air filter Air filterAir filter Internal clock battery Remove the battery coverInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensInternal temperature is rising TroubleshootingMessage Description There is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Not properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter 997-5215-00MU03642Specifications 319 418 139 154 Unit mmPlanar Systems, Inc Corporate Headquarters NW Compton Drive Beaverton, or
Top Page Image Contents