Planar PR9020 user manual Image Menu, Over Scan, Position

Page 31

IMAGE Menu

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For an RGB signal

 

NORMAL ó 4:3 ó 16:9 ó SMALL

 

For an HDMI signal

ASPECT

NORMAL ó 4:3 ó 16:9 ó 14:9 ó SMALL

For a Video signal, S-video signal or Component video signal

 

 

4:3 ó 16:9 ó 14:9 ó SMALL

 

For no signal

 

4:3 (fixed)

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

Using the ▲/▼ buttons adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video, component and HDMI signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

• Over-adjusting the vertical position may cause noise to appear on the screen. If this

V POSITION

occurs please reset the vertical position to the default setting. Pressing the RESET button

when the V POSITION is selected will reset the V POSITION to the default setting.

 

• When this function is performed on a video signal, s-video signal, or component video

 

signal of 525i (480i) or 625i (576i) input from the COMPONENT port, the range of this

 

adjustment depends on the OVER SCAN (above) setting. It is not possible to adjust

 

when the OVER SCAN is set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

• Over-adjusting the horizontal position may cause noise to appear on the screen. If this

H POSITION

occurs please reset the horizontal position to the default setting. Pressing the RESET

button when the H POSITION is selected will reset the H POSITION to the default setting.

 

• When this function is performed on a video signal, s-video signal, or component video

 

signal of 525i (480i) or 625i (576i) input from the COMPONENT port, the range of this

 

adjustment depends on the OVER SCAN (above) setting. It is not possible to adjust

 

when the OVER SCAN is set to 10.

(continued on next page)

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents PR9020 LCD Projector Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Fastening the lens cover Contents of packageHOT Part namesProjector HOTVideo port &10 Control panelRear panel Control port &10 Hdmi port &10Back Remote control Remote controlLaser pointer &13 It is a beam outlet Setting up Suspended from the ceiling ArrangementOn a horizontal SurfaceUsing the security bar and slot Adjusting the projectors elevatorSpeakers wiht an amplifier Connecting your devicesUSB storage SD card Remote control MonitorAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord To the outlet Connecting power supplyHitachi MAXELL, Part No.LR6 Remote controlLaser pointer Putting batteriesBack sensor About the remote control signalChanging the frequency of remote control signal Front and top sensorsUsing as a simple PC mouse & keyboard Using as a wired remote controlSTANDBY/ON button Power indicator Power switch Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating For an Hdmi signal Searching an input signalSelecting an input signal  For an RGB signal For a video signal and s-video signal Adjusting the zoom and focusAdjusting the lens shift Using the automatic adjustment featureCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Enter button Using the menu functionEasy Menu Advanced MenuKeystone Picture ModeAspect AutoEasy Menu Gamma Picture MenuColor Temp Picture MenuSAVE-1, SAVE-2, SAVE-3, SAVE-4 Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 MY MemoryOver Scan Image MenuPosition Size PhaseAuto Adjust Image MenuInput Menu Hdmi Input MenuComponent Video FormatDescription Resolution Setup Menu Setup Menu Audio Menu Or keep no operation for about 10 seconds Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Screen MenuStart UP Screen MenuMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Filter Message GhostLens Type Remote Freq Factory ResetKEY Lock Remote ReceivSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off SecurityTurning Off the PIN Lock Function Description SecurityIf you have forgotten your PIN Code Setting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network Menu SetupNetwork Menu Name ProjectorEnter or Input button Use the / buttons To switch the image displayedPress the or ESC button on the remote control Description ShotInformation Part number = MaintenanceCase of replacement by yourself LampLamp Lamp warningAir filter Cleaning the air filterAir filter Remove the battery cover Internal clock batteryCaring for the lens Caring for the cabinet and remote controlOther care Inside of the projectorRelated messages TroubleshootingMessage Description There is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedPhenomena that may be easily mistaken for machine defects Whisper function is working Color settings are not correctly adjustedColor Space setting is not suitable Not properly adjustedAir filter 997-5215-00MU03642 Warranty and after-serviceSpecifications Specifications319 418 139 154 Unit mm SpecificationsCorporate Headquarters NW Compton Drive Beaverton, or Planar Systems, Inc
Top Page Image Contents